CBE 520 Скачать руководство пользователя страница 47

Страница: 47 / 61

◙ If correctly connected, try a Calibration Reset. Press <

CAL

> and when "FirstZero?"

is displayed press <

SELECT

> until Cal Reset is displayed. Press <

ENTER

> to reset

and recalibrate the indicator.

◙ If Calibration Reset does NOT work, hook a load cell simulator up to the indicator to

test and make sure indicator is working correctly.

Troubleshooting

◙ If load cell simulator works fine, hook the load cell back up to the indicator.

◙ Go into setup: 100<

SELECT

>23640<

TIMERS

& ADJUST

ENTER

◙ Key in 110<

SELECT

> and enter a weight HIGHER than currently in the indicator. If

100 lbs, set to 250. To do this, just key in the desired weight and press <

ENTER

◙ Once the desired weight is entered, press <

ZERO

>, when prompted "Enter=Cal!"

press <

ENTER

> and proceed through calibration.

◙ Once calibrated, if "Cal good?" displays on indicator, press <

ENTER

> through

remaining prompts.

Troubleshooting

◙ Once back in weigh mode, re-enter setup and go back to parameter 110.

◙ Change the newly keyed in value back to original weight value, and proceed to

calibrate once again by pressing <

ZERO

> and <

ENTER

> to re-

calibrate.

◙ USE THE NEXT STEPS AS A LAST RESORT!

◙ If this still does NOT fix the issue, the indicator MAY need to be defaulted at P65001.

Key in 100<

SELECT

>23640<

TIMERS & ADJUST

ENTER

> to enter setup.

◙ Key in 65001<

SELECT

> to get "Defit All" and press <

ENTER

> through the prompts.

◙ The program will NEED to be reloaded and the indicator re-calibrated.

Содержание 520






























































Результаты поиска

Содержание 520

Отзывы:

Бренды по названию

Популярные бренды

CBE 520, Безопасность, Установка, Эксплуатация, Обслуживание

Результаты поиска

Содержание 520

Отзывы:

Бренды по названию

Популярные бренды