106
Unit Initiates a Humidi-MiZer
Dehumidification Mode, but
Supply Air Temperature is
Overheating/Overcooling the
Space
Supply air set point for cooling is too
high/low
Check the unit supply air set point for cooling operation. This is the
temperature that the valves will modulate to meet during a
dehumidification mode.
Evaporator discharge temperature
(CCT) or supply air temperature (SAT)
thermistor is reading incorrectly
See “Thermistor Troubleshooting” on page 103.
Check if SAT thermistor is in a location that is measuring stratified air.
Valve controlling gas bypass around
the condenser is not functioning
properly
See “Modulating Valves Not Functioning Properly.”
Valve controlling refrigerant flow to the
condenser is not functioning properly
See “Modulating Valves Not Functioning Properly.”
Modulating valves are not calibrated
properly
See “Modulating Valves Not Functioning Properly.”
Unit control software indicates a
Humidi-MiZer Reheat Mode, but the 3-
way valve is not functioning properly.
See “3-Way Valve Malfunction.”
Unit is not sized to meet the load at the
current entering air and outdoor
conditions.
Check product data tables or ECAT for rated capacity at current
entering air and outdoor conditions.
Low Sensible Capacity in Normal
Cooling Mode
Valve controlling gas bypass around
the condenser is stuck in an open
position or leaking.
See “Modulating Valves Not Functioning Properly.”
Valve controlling refrigerant flow to the
condenser is stuck in a position less
than 100% open.
See “Modulating Valves Not Functioning Properly.”
General cooling mode problem
See Table 72.
Modulating Valves Not
Functioning Properly
Faulty wire connections
Check that the valve wiring is properly connected from the valve,
entering the control box and at the EXV board.
EXV board malfunction
Check alarm history for A169 (Expansion Valve Control Board Comm
Failure.)
Valve is stuck open/closed
Use Service Test to manually manipulate the valve position and confirm
supply air temperature changes during operation.
Run valve calibration through Service Test.
Check valve motor for open or short circuited windings. Shut down
power to the unit and connect ohmmeter probes across the black and
white terminals. Resistance should measure 75 ohms ±10%. Next,
connect ohmmeter probes across the red and green terminals.
Resistance should measure 75 ohms ±10%. The meter should not
show an “open” or a “short” when a winding leg is measured. If either
occurs, replace the valve.
Valve is not calibrated properly.
Run valve calibration through Service Test.
Table 73 — Humidi-MiZer
®
Service Analysis (cont)
PROBLEM
CAUSE
REMEDY
Содержание WeatherExpert 48N2
