Carrier WeatherExpert 48N2 Скачать руководство пользователя

Страница: 65 / 268

LAT Limit Config (LAT.L)

This configuration senses when leaving air temperature is out

side a delta temperature band around set point and allows stag

ing to react quicker.

Heat Control Prop. Gain (HT.P)

This configuration is the proportional term for the PID, which

runs in the HVAC mode LOW HEAT.

Heat Control Derv. Gain (HT.D)

This configuration is the derivative term for the PID, which

runs in the HVAC mode LOW HEAT.

Heat PID Rate Config (HT.TM)

This configuration is the PID run time rate.

Staged Heating Logic

If the HVAC mode is HIGH HEAT:

• On 48N units, the supply fan for staged heating is con

trolled by the integrated gas control (IGC) boards and, un

less the supply fan is on for a different reason, will be con

trolled by the IFO. On 50N units, the fan is ON whenever

the heat is ON.

• Command all stages of heat ON.

If the HVAC mode is LOW HEAT:

• On 48N units, the supply fan for modulating gas heating is

controlled by the integrated gas control (IGC) boards and,

unless the supply fan is on for a different reason, will be

controlled by the IGC IFO input. On 50N units, the fan is

ON whenever the heat is ON.

• The unit will control stages of heat to the heating control

point (

Run Status



VIEW



HT.C.P

). The heating control

point in a LOW HEAT HVAC mode for staged heat is the

heating supply air set point (

Setpoints



SA.HT

Staged Heating PID Logic

The heat control loop is a PID design with exceptions, over

rides, and clamps. Capacity rises and falls based on set point

and supply-air temperature. When the

Comfort

Link control is

in Low Heat or Tempering Mode (HVAC mode), the algorithm

calculates the desired heat capacity. The basic factors that gov

ern the controlling technique are:

• how frequently the algorithm is run.

• the amount of proportional and derivative gain applied.

• the maximum allowed capacity change each time this al

gorithm is run.

• deadband hold-off range when rate is low.

This routine is run once every “

HT.TM

” seconds. Every time

the routine is run, the calculated sum is added to the control

output value. In this manner, integral effect is achieved. Every

time this algorithm is run, the following calculation is per

formed:

Error =

HT.C.P

–

LAT

Error_last = error calculated previous time

P =

HT.P

*(Error)

D =

HT.D

*(Error

–

Error_last)

The P and D terms are overridden to zero if:

Error <

S.G.DB

AND Error >

–

S.G.DB

AND D <

M.R.DB

AND D >

–

M.R.DB.

“P + D” are then clamped based on

CAP.M

This sum can be

no larger or no smaller than +

CAP.M

or –

CAP.M

Finally, the desired capacity is calculated:

Staged Heat Capacity Calculation = “P + D” + old Staged Heat

Capacity Calculation.

NOTE: The PID values should not be modified without ap

proval from Carrier service personnel.

Modulating Gas Heat Staging

Different unit sizes will control heat stages differently based on

the amount of heating capacity included. These staging patterns

are selected based on the unit model number. The selection of a set

of staging patterns is controlled via the heat stage type configura

tion parameter

Configuration→HEAT→SG.CF→HT.ST

. Set

ting

HT.ST

to 0, 1, 2, or 3 configures the unit for Modulating Gas

Heat. The selection of

HT.ST = 0, 1, 2, or 3

is based on the unit

size and heat size. See Table 38.

Table 38 —

Modulating Gas Heat

As the heating capacity rises and falls based on demand, the

modulating gas control logic will stage the heat relay patterns

up and down respectively (

Run Status→VIEW→HT.ST

) and

set the capacity of the Modulating Gas section (

Outputs

→HEAT→H1.CP

). The Heat Stage Type configuration selects

one of the staging patterns that the modulating gas control will

use. In addition to the staging patterns, the capacity for each

stage is also determined by the modulating gas heating PID al

gorithm. Therefore, choosing the heat relay outputs and setting

the modulating gas section capacity is a function of the capaci

ty desired, the available heat staging patterns configured with

heat stage type (

HT.ST

), and the capacity range presented by

each staging pattern.

As the modulating gas control desired capacity rises, it is con

tinually checked against the capacity ranges of the next higher

staging patterns. Since each stage has a range of capacities, and

the capacities of some stages overlap, the control selects the

highest stage with sufficient minimum capacity.

Similarly, as the modulating gas control desired capacity drops,

it is continually checked against the capacity ranges of the next

lower stages. The control selects the lowest stage with suffi

cient maximum capacity.

The first 2 modulating gas heat outputs are located on the

MBB. Outputs 3, 4, 5, 6, and the analog output that sets the

modulating gas section capacity are located on the SCB out

puts 7 and 8 are located on the CXB. The heat stage selected

(

Run Status→VIEW→HT.ST

) is clamped between 0 and the

maximum number of stages possible (

Run Status

→VIEW→H.MAX

). See Tables 39-42.

SCR Electric Heat Staging

For all SCR electric heat units there is only 1 heat stage. When

ever the heat is energized, all heaters are active and modulated

through the SCR control.

IMPORTANT: When gas or electric heat is used in a VAV

application with third-party terminals, the HIR relay output

must be connected to the VAV terminals in the system in or

der to enforce a minimum heating cfm. The installer is re

sponsible to ensure the total minimum heating cfm is not be

low limits set for the equipment. Failure to do so will result

in limit switch tripping and may impair or negatively affect

the Carrier product warranty.

NUMBER

STAGES

HT.ST

CONFIG.

NO. OF HEAT

EXCHANGER

SECTIONS

UNIT SIZE

48N

HEAT

SIZE

75, 90, 105

Low

High

90, 105

Med

120,130,150

Low

90-105

High

120,130,150

Med

120,130,150

High

Содержание WeatherExpert 48N2













































































































































































































































































Результаты поиска

Содержание WeatherExpert 48N2

Отзывы:

Похожие инструкции для WeatherExpert 48N2

Бренды по названию

Популярные бренды

Carrier WeatherExpert 48N2, Управление, пуск, эксплуатация, обслуживание и устранение неисправностей.

Результаты поиска

Содержание WeatherExpert 48N2

Отзывы:

Похожие инструкции для WeatherExpert 48N2

Бренды по названию

Популярные бренды