manualshive.com logo in svg

Carlton SP5014TRX, Руководство пользователя

Поделиться
Скачать
Carlton SP5014TRX Скачать руководство пользователя страница 67

SP5014TRX        SERVICING CUTTER WHEEL

 

 

47

 

SAFETY 

 

NEVER SERVICE A MACHINE WITH THE ENGINE RUNNING, SEVERE 
PERSONAL INJURY COULD OCCUR.  TURN ENGINE OFF THEN REMOVE 
IGNITION KEY AND DISCONNECT POSITIVE BATTERY CABLE TO AVOID 
STARTING MACHINE ACCIDENTALLY. 

 

CUTTER WHEEL MUST BE DISENGAGED BEFORE TURNING ENGINE 
ON/OFF AND BEFORE SERVICING A MACHINE.  OTHERWISE SEVERE 
PERSONAL INJURY COULD OCCUR AS WELL AS MACHINE DAMAGE. 

 

ALL MACHINE PARTS MUST COME TO A COMPLETE STOP AND HAVE 
TIME TO COOL COMPLETELY BEFORE SERVICING A MACHINE OR 
SEVERE INJURY COULD OCCUR, POSSIBLY SERIOUS BURNS AND/OR 
DISMEMBERMENT. 

 

DO NOT OPERATE A MACHINE WITHOUT A COMPLETE NUMBER OF 
TEETH IN THE CUTTER WHEEL PROPERLY INSTALLED.  EXCESSIVE 
MACHINE VIBRATION WILL OCCUR CAUSING PREMATURE BEARING 
FAILURE AND EQUIPMENT DAMAGE. 

 

PLACE THE CUTTER WHEEL ON THE GROUND WHEN PERFORMING 
SERVICE ON A MACHINE. 

 
 

 

There are twenty (20) teeth to a complete set 
on the model SP5014TRX.  Two (2) straight 
teeth, nine (9) left 45° teeth and nine (9) right 
45° teeth. 

 
 
 
 

 

A locking pin is provided to hold cutter 
wheel in position during tooth removal and 
re-installation.  Locking pin will only lock on 
outer teeth. 

NEVER PLACE HAND ON CUTTER 
WHEEL TO HOLD IN PLACE WHILE 
CHANGING TEETH.  BE SURE TO 
REMOVE PIN BEFORE OPERATING. 

 
 

 

A Tooth Setting Gauge

 (P/N 0450111)

 is 

provided with each machine for proper tooth 
installation.  Line all teeth up with the inside 
edge of the groove in the gauge.  Set 

ALL

 

teeth to this edge with gauge against pocket, 
not against cutter wheel. 

See Cutter Wheel Assembly for 
breakdown. 

 

 

 

 

 

Содержание SP5014TRX

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды