manualshive.com logo in svg

Carlton SP5014TRX, Руководство пользователя

Поделиться
Скачать
Carlton SP5014TRX Скачать руководство пользователя страница 56

SP5014TRX                            SERVICING BELTS

 

 

36

 

Replacing Poly Chain

®

 Belt

 

 
 

 

Check alignment of Poly Chain

®

 sprockets 

using a straight edge. 

 
 
 
 
 
 
 
 
 
 
 

 

To adjust tension of the belt, slide the 
bearings back into the place that you had 
marked.  Tighten the jam bolts.  To tighten 
the belts more if needed, loosen the front jam 
bolts and tighten each of the back jam bolts 
the same number of revolutions, to keep the 
alignment true.  After the belt is adjusted, 
tighten the front jam bolts back against the 
bearing.  

After the Poly Chain

®

 

belt has 

been adjusted; check the

 

V-belt tension 

and alignment.  When the V-belt is 
tensioned properly, it will deflect 1/4” with 
25 lbs. of force applied.

 

 
 
 
 
 
 

 

Replace Poly Chain

®

 belt guard cover and 

bottom cover and tighten bolts. 
DO NOT RUN MACHINE WITHOUT ALL 
GUARDS IN PLACE AND SECURED. 

 

 

 

 

 
 
 
 
 

 

Содержание SP5014TRX

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды