Carlton SP5014TRX Скачать руководство пользователя страница 63

Страница: 63 / 160

SP5014TRX SERVICING BEARINGS

Replacing Cutter Wheel Bearings



Loosen jam bolts in the back of the jackshaft
bearings and move bearings back to remove
the Poly Chain

belt. You may need to

unbolt V-belt guard and lift jackshaft end up
to remove belt.



Remove the four bolts on the cutter wheel
bearings. Cutter wheel will be free from
machine at this point. With the Poly Chain

belt removed, you can start the machine and
raise the boom up.



Cut the cutter wheel shaft on one side of the
cutter wheel so that you can get the cutter
wheel off of the shaft.



Remove Poly Chain

sprocket by removing

the bolts inside the sprocket and tapered
bushing. Then screw one bolt into third hole
to push sprocket off tapered bushing to
remove.

Содержание SP5014TRX

































































































































































Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды

Carlton SP5014TRX, Руководство пользователя

Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды