manualshive.com logo in svg

Carlton SP5014TRX, Руководство пользователя

Поделиться
Скачать
Carlton SP5014TRX Скачать руководство пользователя страница 28

SP5014TRX                   SAFETY PRECAUTIONS

 

 

8

ATTENTION: 

The Carlton

®

 Model SP5014TRX Stump Grinder 

CAN

 be overturned on steep inclines. 

This can cause serious injury to operator and machine. 

DO NOT OVERTURN!

 

 
 

 

 
 
 
 

 

Avoid steep side inclines when operating 
this machine!  The narrow design width 
required in operating the model 
SP5014TRX in tight confines makes it 
susceptible to tipping over sideways.  
Overturning this machine can result in 
personal injury, property damage and/or 
seizing the engine.  

USE CAUTION.

 

 

 

Positioning the

 cutter wheel uphill

 and 

as close to the ground as possible while 
in transit will minimize the danger of 
tipping over and maximize the 
steadiness of the Model SP5014TRX.

 

 

 

When encountering a hill, the best 
approach is straight up or straight down.  
Avoid any side angles whenever 
possible. 

NEVER ALLOW INEXPERIENCED 
PERSONS TO OPERATE THIS 
MACHINE. 

 

 
 
 
 
 

 

P/N 0700024 

Содержание SP5014TRX

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды