Carlton SP5014TRX Скачать руководство пользователя страница 22

Страница: 22 / 160

SP5014TRX GENERAL INFORMATION

The J. P. Carlton Company constantly strives to create the best professional tree equipment

available in the industry. Therefore, the material in this manual is correct at the time of
publication. Carlton

reserves the right to make improvements, modifications, and even

discontinue features as we deem necessary to meet our goal. Carlton

also reserves the right to

discontinue models without any prior notification or obligation.

Inspect your new Carlton Stump Cutter as soon as you receive it. Any damages incurred

during shipment are not warranted and, therefore, are not covered repairs. You should have the
truck driver verify or acknowledge any damages caused during shipment. If not, contact the truck
lines as soon as possible with your complaint.

Any reference made to the right, left, front, or rear in relationship to the chipper is illustrated in

the following pictures. Please refer to these any time you call your dealer or J. P. Carlton for
parts or assistance.

Left

Right

Front

Rear

Front

Содержание SP5014TRX

































































































































































Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды

Carlton SP5014TRX, Руководство пользователя

Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды