Carlton SP5014TRX Скачать руководство пользователя страница 44

Страница: 44 / 160

SP5014TRX MACHINE MAINTENANCE



Check cutter wheel, pockets, and teeth for
wear. If any repair is needed, see “Servicing
Cutter Wheel” section for further
instruction.

Always clean tip of grease gun fitting and grease fitting on machine before attaching hose
to prevent dirt from being forced into machine parts.



Grease jackshaft bearings

daily

. These

bearings should be purged using grease

EVERYDAY.

Purge till new grease comes

out. Use Texaco

Starplex II grease.

Always clean tip of grease gun fitting and
grease fitting on machine before attaching
hose to prevent dirt from being forced
into machine parts.



Grease cutter wheel bearings

Daily

. These

bearings should be purged using grease

EVERYDAY.

Purge till new grease

comes

out. Use Texaco

Starplex II grease.

Always clean tip of grease gun fitting and
grease fitting on machine before attaching
hose to prevent dirt from being forced
into machine parts.



Grease engine slide assembly every 15 – 20
hours of operation with approximately 2 to 4
shots of Texaco

Starplex II grease. (Total

of 6 grease fittings.)

DO NOT OVER

GREASE.



Grease engagement lever every 15 – 20
hours of operation with approximately 2 to 4
shots of Texaco

Starplex II grease.

ENGAGEMENT LEVER

GREASE FITTINGS

Содержание SP5014TRX

































































































































































Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды

Carlton SP5014TRX, Руководство пользователя

Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды