manualshive.com logo in svg

Carlton SP5014TRX, Руководство пользователя

Поделиться
Скачать
Carlton SP5014TRX Скачать руководство пользователя страница 52

SP5014TRX                            SERVICING BELTS

 

 

32

 

Replacing V-Belt 

 

 

If the belt tension was adjusted, the engine 
slide lock will also have to be adjusted.  This 
locks the engine in the disengaged position 
so that the cutter wheel will not accidentally 
engage.  When adjusting the engine slide 
lock, turn the clevis clockwise to shorten the 
length of the engine slide lock when the 
engagement linkage was lengthened.  The 
engagement linkage would be lengthened to 
put more tension on the belt.  Lengthen the 
engine slide lock if the engagement linkage 
was shortened. 

 
 
 

 

Replace hydraulic pump making sure the 
insert is in place. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Retighten all five belt-keepers when the belt 
tension has been adjusted.  There are two belt 
keepers on the jackshaft sheave.  The beehive 
has two belt keepers inside it, one on top and 
one on bottom.  The last belt keeper is beside 
the beehive. 

 

 
 
 
 

 

 
 
 

 

 
 
 
 
 
 

 

 

 

REPLACE THE RUBBER INSERT 

WHEN REATTACHING THE PUMP 

BELT KEEPERS 

Содержание SP5014TRX

































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды