Carlton SP5014TRX Скачать руководство пользователя страница 59

Страница: 59 / 160

SP5014TRX SERVICING BEARINGS

Replacing Jackshaft Bearings



Remove Poly Chain

belt guard cover and

bottom cover.



Remove Poly Chain

sprocket by removing

the bolts inside the sprocket and tapered
bushing. Then screw one bolt into third hole
to push sprocket off tapered bushing to
remove.



You may cut the jackshaft between the
bearings and the Poly Chain

guard.



Remove old bearings and shaft and replace
with new bearings and shaft. Be sure to turn
jackshaft with the longest keyway pocket
toward the Poly Chain

belt side of the boom

and make sure that the locking collars on the
bearings are facing inward. Bolt new
bearings and jackshaft back into place. Just
snug bolts down, do not tighten all the way
down, you will need to move them later to
adjust belt tension.

Содержание SP5014TRX

































































































































































Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды

Carlton SP5014TRX, Руководство пользователя

Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды