Carlton SP5014TRX Скачать руководство пользователя страница 48

Страница: 48 / 160

SP5014TRX TROUBLESHOOTING GUIDE

COMPLAINT

CAUSE CORRECTION

Cutter wheel stops turning.



Belt not engaged.



Engine belt broke.



Poly chain® belt broke.



Sheared key in shaft.



Broke cutter wheel shaft.



Adjust yoke assembly.



Replace belt.



Replace belt.



Replace key.



Replace shaft.

Roar in machine when cutter
wheel is engaged.



Belt guards rubbing on
jackshaft or cutter wheel
shaft.



Jackshaft or cutter wheel
bearings going bad.



Re-position guards off of
shafts.



Replace bearings.

Traction loss of power.



Relief valve set too low.



Hydraulic motor worn.



Increase relief valve
pressure by turning relief
valve screw inward.



Replace Hydraulic motor.

Bearing will not take grease.



Grease fitting clogged.



Replace fitting

Cutter head swings faster one
way than the other.



Counter balance valve is
out of adjustment.



Adjust counter balance
valve to equalize swing
speed.

For all Radio Transmitter or Receiver problems, see the Radio Control Manual included at
the back of this manual.

Содержание SP5014TRX

































































































































































Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды

Carlton SP5014TRX, Руководство пользователя

Результаты поиска

Содержание SP5014TRX

Отзывы:

Бренды по названию

Популярные бренды