Carel optiMist EC005 0 Series, Руководство пользователя

Страница: 37 / 46

37
ENG
“optiMist” +0300065EN - rel. 1.6 - 18/06/2021
Display Description Range Def. UOM
Start
Start maximum humidification rack
flow-rate calibration Yes, No No
Offset
Inverter offset setting in hertz 0 Hz
Open steps
Display the number of open steps 0-2
Production Display inverter hertz at minimum rack
flow-rate Hz
Pressure
Display water pressure at maximum
rack flow-rate bar
Tab. 8.aj
Display Description Range Def. UOM
Start
Start minimum humidification rack
flow-rate calibration for Indirect
Evaporative Cooling (IEC) Yes, No No
Offset Inverter offset setting in hertz 0 Hz
Open steps
Display the number of open steps 0-2
Production
Display inverter hertz at minimum
rack flow-rate Hz
Pressure
Display water pressure at minimum
rack flow-rate bar
Tab. 8.ak
Display Description Range Def. UOM
Start
Start maximum humidification rack
flow-rate calibration for Indirect
Evaporative Cooling (IEC) Yes, No No
Offset
Inverter offset setting in hertz 0 Hz
Open steps
Display the number of open steps 0-2
Production
Display inverter hertz at minimum
rack flow-rate Hz
Pressure
Display water pressure at maximum
rack flow-rate bar
Tab. 8.al
Display Description Range Def. UoM
CHANGE PASSWORD
Insert new instal-
ler password
Change installer password 0000 to 9999 77
Tab. 8.am
Submenu: 2. Zone Menu - 4. Supervision
Display Description Range Def. UoM
CONFIG.SUPERVISION 1/2
Id for
BMS:
Supervision address
selection NO, ID8 (life sign
control other
cabinet from digital
input), BMS N.O
Baudrate:
communication speed
between the pCO and the
supervisory system 1200,2400,4800,
9600,19200 19200 bps
Protocol
type
Type of communication
protocol Carel, Modbus, Lon,
RS232, WinLoad Carel hours
Tab. 8.an
Display Description Range Def. UoM
CONFIG.SUPERVISION 2/2
On/Off from
Superv.
Enable on/off from supervision NO,YES NO
Control from
Superv (Hu-
mid)
Enable control from supervision
(Humidification if Humidification
+IEC configuration) NO,YES NO
Control from
Superv IEC
Enabled control from IEC
supervision NO,YES NO
Tab. 8.ao
Submenu: 2. Zone Menu - 5. External Alarms
Display Description Range Def. UoM
External Alarms
Droplet
separator
alarm
logic
Droplet separator
differential
pressure switch
alarm input logic N.O. = (normally open) when
connecting as described in
the previous paragraphs,
optiMist will show the
Water treatment alarm if the
connection is interrupted or, N.C
N.C. = (normally closed) when
connecting as described in
the previous paragraphs,
optiMist will show the
Water treatment alarm if the
connection is not interrupted
(contact closed)
Tab. 8.ap
Submenu: 3. - Wizard
In this section, which can be accessed on start-up or through the Installer
menu, the fundamental machine start-up parameters can be set.
The screens in this section, recall the parameter settings mainly covered
in the sections “Input configuration” and “Distribution System” shown
previously.
8.13 Maintenance menu
Attenzione:
le operazioni descritte in questo menu devono essere
esclusivamente eseguite da personale qualifi cato.
From the main screen press:
•
PRG to access the main menu;
•
DOWN to move to the installer menu;
•
ENTER to move to the password;
•
UP/DOWN to enter the password “77“
•
ENTER to access the selected menu;
•
UP/DOWN to move between the submenus;
•
ENTER to select the parameter and move between the parameters;
•
UP/DOWN to modify the parameter;
•
ENTER to confirm the selected parameter and go to the next parameter;
•
ESC to return to the previous menu.
Installer menu screens:
Display
1. Reset conf
2. System info
3. Instantaneous readings
4. Manual procedure
5. System status info
6. Hour gauge
7. Alarm history
Submenu: 1.Reset conf
Display Description Range Def.
Reset config.
Reset default:
Activating recalls the
default factory settings NO,YES NO
Set model Setting the machine
model All machine
models available The same model
shown on the
cabinet label
Tab. 8.aq