Carel MPXone ACS00CB000010 Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 108

background image

5. Functions

If the settings made during commissioning are not sufficient to achieve the desired operation, further
(detailed) configuration of the parameters can be performed, as described in the following paragraphs.
The parameters described below can be configured via the configuration software or the "APPLICA" app.

Important:

the information available in Applica may vary according to the password set and the

configuration set by the unit manufacturer, and consequently not all the parameters shown may be
visible or modifiable.
For details on the parameters and the related access levels, see the "Parameter table".

5.1
Inputs and
outputs

MPXone features up to 6 analogue inputs and 5 digital inputs. See the description of the terminals in the
paragraph "Description of the terminals".
The probes (temperature NTC, PT1000, 0-5 Vdc ratiometric and active probes), can be connected to the
analogue inputs, and have been divided into 3 groups, with the same type of probe for each group. See
the parameter table.

Probes

Outputs (Y1, Y2)

Model

Part number

Passive

Active

NTC
(–
50T90°C)

Pt1000

(–

50T150°C)

0 to 5 V
ratiometric

4 to 20
mA

0 to 10 V active
probes

PWM

0 to
10
Vdc

BASIC

S1M0004W0B06
(0/1)

YES

NO

NO

NO

NO

NO

NO

MEDIUM

S1M0006W0B07
(0/1)

YES

YES

YES

YES

YES

YES

YES

S1M0006B0B08
(0/1)

YES

YES

YES

YES

YES

YES

YES

S1M0007N0B11
(0/1)

YES

YES

YES

YES

YES

YES

YES

Important:

observe the maximum allowable current limits on the relays. See the technical

specifications table.

5.1.1 Probes (analogue inputs)

MPXone version

Basic

Medium

Analogue input

S1

S2

S3

S1

S2

S3

S4

S5

S6

Parameter for type of probe

/P1

/P1

/P2

/P3

0 = PT1000 Standard (Range –50T150 °C)

1 =NTC Standard (Range –50T90 °C)

2 = 0-5V ratiometric probe

3 = 4-20 mA input

4 = 0-10V input

Important:

for the maximum current that can be supplied to the ratiometric probes, see the technical

specifications table

Inputs S4, S5 and S6 can be connected to 0-5 V ratiometric pressure probes and active probes with 4-20
mA or 0-10 V output (S6 only). All these probes require the range of measurement to be defined, set by
the relative minimum and maximum parameters for the function associated with the probe. See the
parameter table.
To assign the function to each physical or serial probe, configure parameters /FA, /Fb, ... /Fn. See the
parameter table.

ENG

0300086EN rel. 1.0 – 04.09.2018

5. Functions |

37

«
...
35
36
37
38
39
...
»

Содержание MPXone ACS00CB000010













































































































Отзывы:

Нет отзывов

Похожие инструкции для MPXone ACS00CB000010

AF-600 FP Series

Бренд: GE Страницы: 7

Бренд: Jafar Страницы: 9

Бренд: Lattice Semiconductor Страницы: 30

Бренд: WAFER Страницы: 15

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

HomeTec Pro CFF3000

Бренд: Abus Страницы: 13

Бренд: NAVITAS Страницы: 7

Бренд: Abus Страницы: 2

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 12

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 44

Бренд: FAAC Страницы: 8

Бренд: FAAC Страницы: 60

Бренд: FAAC Страницы: 14

Бренд: FAAC Страницы: 68

Бренд: FAAC Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды