Carel MPXone ACS00CB000010 Скачать руководство пользователя | Manualshive

Страница: 30 / 108

background image

ENG

different parameter visibility depending on the rights associated with each profile (User, Service,
Manufacturer).

Procedure:

1. download the “Applica” app for Android devices from Google Play;
2. (on the mobile device) start the app for commissioning the controller;
3. activate NFC;
4. move the device closer to the controller, less than 10 mm away;
5. follow the instructions shown on the display.

3.2.5 Direct functions

The following functions can be activated directly from the keypad or via the app:

Icon

Display On/Off

Lht

Cabinet light

+

Cnt

Continuous cycle

dEF

Defrost

+

CLn

Clean cabinet

ON

Unit ON

+

rH

Anti-sweat heater

Procedure:

1. go to the standard display;
2. press PRG: Lht is displayed;
3. press PRG to turn the light on/off and DOWN to move to the next direct function;
4. follow the previous steps for all the other functions;
5. When finished, press Esc to exit.

1. Go to the standard display;

2. Press PRG: Lht is displayed, the UP
and DOWN buttons light up.
Press PRG to turn the light on/off: the
icon will come on or go off.
Press DOWN to activate the next
function (Cnt) or press Esc to exit;

3. Press PRG to activate the
continuous cycle (Cnt).
Press DOWN to activate the
next function;

4. Follow the previous steps for all
the other functions;

5. Select Esc to exit;

6. The standard display is
shown

30

| 3. User interface

0300086EN rel. 1.0 – 04.09.2018

«
...
28
29
30
31
32
...
»

Содержание MPXone ACS00CB000010













































































































Отзывы:

Нет отзывов

Похожие инструкции для MPXone ACS00CB000010

Бренд: GBD Страницы: 12

Бренд: National Instruments Страницы: 10

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: Quickmill Страницы: 3

Бренд: 2N Страницы: 4

Бренд: eclisse Страницы: 40

Бренд: IDK Страницы: 96

FSDrive-MV1000 Series

Бренд: YASKAWA Страницы: 260

Бренд: YASKAWA Страницы: 114

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 152

Бренд: YASKAWA Страницы: 66

Бренд: YASKAWA Страницы: 20

Бренд: YASKAWA Страницы: 17

Бренд: YASKAWA Страницы: 58

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA Страницы: 58

ZITON RADIO LOOP MODULE

Бренд: EMS Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды