Carel MPXone ACS00CB000010 Скачать руководство пользователя | Manualshive

Страница: 42 / 108

background image

ENG

Immediate external alarm (par. DIA)

Activation of the alarm causes:

l

message ‘IA’ shown on the display and ALARM flashing;

l

activation of the buzzer (see par. H8);

l

activation of the alarm relay (see par. DOb);

l

deactivation of the solenoid/compressor output (see par. A10).

Nota:

activation of the external alarm shuts down the evaporator fans only if these follow the status of

the compressor output, as set for parameter F2. When the compressor is shut down due to an external
alarm the compressor ON time is ignored (parameter c3).

Code Description

Def Min Max UOM User

User

terminal

DIA

Assign immediate external alarm digital input

0 = Function disabled

4 = digital input 4 (ID4)

1 = digital input 1 (ID1)

5 = digital input 5 (ID5)

2 = digital input 2 (ID2)

-1 = digital input seriale

3 = digital input 3 (ID3)

0

-1

5

-

S

NO

Delayed external alarm (par. DIb)

The behaviour of this alarm is the same as for the immediate external alarm, with a delay in activation. If
set to 0, the alarm is signal-only.

Code Description

Def Min Max UOM User

User

terminal

DIb

Assign delayed external alarm digital input - see DIA

0

-1

5

-

S

NO

A11

Delay time for delayed external alarm
0 = Signal-only alarm

0

0

14

-

S

NO

Enable defrost (par. DIc)

Used to disable any defrost calls. When the contact is open, all defrost calls are ignored. Par. d5 can be
used to delay activation.

Note:

l

if the contact is open while a defrost is in progress, this is immediately stopped, the defrost icon
flashes on the display indicating the defrost call is active (this starts again when the contact closes);

l

this function may be useful to prevent defrosts on units exposed to the public during store
opening hours.

Code Description

Def Min Max UOM User

User

terminal

DIc

Assign enable defrost digital input - see DIA

0

-1

5

-

S

NO

Start defrost (par. DId)

Closing the digital contact starts a defrost, if enabled. With a Master- Slave network connection, if the
controller is the Master, the defrost will be a network defrost, while if it is a Slave, it will only be a local
defrost. The defrost digital input can be used effectively to perform real time defrosts. Simply connect a
timer to the multifunction digital input on the Master and use d5 to delay the defrosts on the various
Slaves and thus avoid current overloads.

Note:

if the defrost is disabled by another digital input configured as “enable defrost”, the defrost

calls are ignored.

Code Description

Def Min Max UOM User

User

terminal

DId

Assign start defrost digital input - see DIA

0

-1

5

-

S

NO

d5

Defrost delay on power-up or (for Slave) after control from

0

0 240 min

S

NO

42

| 5. Functions

0300086EN rel. 1.0 – 04.09.2018

«
...
40
41
42
43
44
...
»

Содержание MPXone ACS00CB000010













































































































Отзывы:

Нет отзывов

Похожие инструкции для MPXone ACS00CB000010

Бренд: YASKAWA Страницы: 256

Бренд: Abicor Binzel Страницы: 8

Бренд: hager Страницы: 62

coviva Smartbox TKP100A

Бренд: hager Страницы: 45

Frigolink FVB110B

Бренд: WURM Страницы: 4

Бренд: Insignia Страницы: 2

FieldPoint FP-AI-100

Бренд: National Instruments Страницы: 17

Бренд: Trane Страницы: 72

ZITON RADIO LOOP MODULE

Бренд: EMS Страницы: 26

Бренд: Danfoss Страницы: 30

Бренд: Daikin Страницы: 64

Q.PEAK DUO BLK ML-G10/t Series

Бренд: Qcells Страницы: 13

Бренд: Fantini Cosmi Страницы: 25

Бренд: Viva Страницы: 9

Бренд: Belimo Страницы: 9

fantech ECO-FEEL 414729

Бренд: SystemAir Страницы: 2

Бренд: Veichi Electric Страницы: 8

Бренд: Flying Industry Development Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды