Carbide 3D Shapeoko HDZ 4.0 Скачать руководство пользователя страница 59

Страница: 59 / 62

[email protected]

docs.carbide3d.com

8/31/2020

Version 4.0

Post Assembly

Update the Software Settings

Update Software

Download and install Carbide Motion from:

https://carbide3d.com/carbidemotion/download/.

Confirm all of the proximity switches and motors are connected correctly, then, ensure that there is nothing

restricting the Shapeoko’s movement.

Update Settings

Now, you’re ready to turn the Shapeoko on and make the required software changes

Connect your machine to Carbide Motion.

Plug in your USB cable.

Open Carbide Motion.

Turn your Shapeoko on.

Click the Connect to Cutter button.

Update your machine settings. See

Fig. 22

Click Settings in the top menu bar.

In the Settings window, choose your
Shapeoko size from the Size dropdown list,
then

choose “HDZ, Full X Travel

(Ballscrew)” from the

‑

Axis Type

dropdown list, and then choose

“Inches”

or “MM” from the

Units dropdown list.

Click the Send Configuration Data button in the middle of the dialog window.

The configuration data will send. Wait until this has finished before moving on to test your proximity switches.

Figure 22

WARNING:

The HDZ is supported by Carbide Motion 4.17 onwards. Do NOT use an older version of Carbide Motion.

WARNING:

NOT

try to home or jog the Shapeoko before applying the updated settings.

Machines With BitSetter:

NOT

enable or re-calibrate your BitSetter at this time. After updating your settings,

checking your proximity switches, and homing, complete the

“Re

Calibrate the BitSetter”

steps on the next page.

Содержание Shapeoko HDZ 4.0































































Результаты поиска

Содержание Shapeoko HDZ 4.0

Отзывы:

Похожие инструкции для Shapeoko HDZ 4.0

Бренды по названию

Популярные бренды

Carbide 3D Shapeoko HDZ 4.0, Инструкция по сборке

Результаты поиска

Содержание Shapeoko HDZ 4.0

Отзывы:

Похожие инструкции для Shapeoko HDZ 4.0

Бренды по названию

Популярные бренды