Carbide 3D Shapeoko HDZ 4.0 Скачать руководство пользователя страница 13

Страница: 13 / 62

[email protected]

docs.carbide3d.com

8/31/2020

Version 4.0

Remove the Y-Axis drag chain head bracket from the outside of the Y1-carriage.

Use an 8mm wrench and a 4mm hex key to remove the two (2) M5 nuts AND the two (2) M5

16mm

SHCS.

Remove the lower two V-wheels from the X/Z-carriage.

Hold the eccentric nuts steady with an 8mm wrench and use a 3mm hex key to remove the V-wheels.

Lift the X/Z-carriage away from the X-rail and lay it on the baseframe.

Disassemble the X/Z-Carriage

Separate the Z-carriage from the X-carriage. See

Fig. 7

Remove the springs from both sides of the
X/Z-carriage.

Loosen the tensioning screw at the
bottom of the X-carriage plate.

Use a 3mm hex key to loosen the
tensioning screw.

Loosen the idler assembly at the bottom
of the X-carriage and free the belt.

Use a 4mm hex key and a 10mm
wrench to loosen the nut holding
the idler in place.

ii.

Free the belt from the idler and
the Z-motor pulley.

Slide the smaller Z-carriage down and away from the larger X-carriage.

Remove the router/spindle mount from the Z-carriage plate.

Use a 3mm hex key to remove the two (2) M5

16mm BHCS securing the mount.

CARRY OVER

the router/spindle mount and M5

16mm BHCS.

Remove the X-motor (lower motor) from the back of the X-carriage plate.

Use a 4mm hex key to remove the four (4) M5

10mm SHCS securing the motor.

CARRY OVER

the X-motor.

Figure 7

Содержание Shapeoko HDZ 4.0































































Результаты поиска

Содержание Shapeoko HDZ 4.0

Отзывы:

Похожие инструкции для Shapeoko HDZ 4.0

Бренды по названию

Популярные бренды

Carbide 3D Shapeoko HDZ 4.0, Инструкция по сборке

Результаты поиска

Содержание Shapeoko HDZ 4.0

Отзывы:

Похожие инструкции для Shapeoko HDZ 4.0

Бренды по названию

Популярные бренды