manualshive.com logo in svg

Canon iR2318 series, Руководство по обслуживанию, Страница: 78 / 308

Поделиться
Скачать
Canon iR2318 series Скачать руководство пользователя страница 78

Chapter 2  

2-24

2.4.4 Installing the Heater PCB

0028-6688

1) Install the heater PCB unit [2].

- Supplied TP screws (M3x8) [1], 2pcs.

2) Install the heater switch [3] on the right side panel.

F-2-55

3) Install the edge saddle [3]. Connect one heater switch harness [1] to the

connector (J1901) on the heater PCB. Route the other harness [2] to the

front of the host machine through the edge saddle [3].

F-2-56

4) Attach the edge saddle [2], then connect the header switch harness [1]

(routed to the front of the host machine) to the connector (J15) on the

power supply PCB through the edge saddle [2]. 

F-2-57

5) Install the three clamps [1] on the back of the host machine.

6) Connect the cassette heater harness [2] to the connector (J1905) on the

heater PCB unit, install the reuse band [3], and then pass the harness

through the clamps installed in step 5).   

F-2-58

7) Install the edge saddle (small) [1].

8) Connect the heater harness [2] to the connector (J1902) on the heater PCB

unit, pass the harness through the installed edge saddle, and then route the

harness to the front of the host machine through the hole [3].

F-2-59

Install the heater switch with the OFF position on the left 
and the ON position on the right just like the main power 
switch.

[2]

[1]

[3]

[1]

[2]

[3]

[2]

[1]

[3]

[2]

[1]

Содержание iR2318 series





















































































































































































































































































































Отзывы:

Нет отзывов