manualshive.com logo in svg

Canon iR2318 series, Руководство по обслуживанию, Страница: 129 / 308

Поделиться
Скачать
Canon iR2318 series Скачать руководство пользователя страница 129

Chapter 4

4-23

20) Remove the reader controller PCB [1] from the mount.

- Screws [2] 3 pcs.

F-4-47

4.4.3 Scanner Motor

4.4.3.1 Removing the Scanner Motor

0020-4391

1) Remove the rear cover.

2) Remove the left cover (rear).

3) Remove the copyboard cover (When the ADF is equipped, open the

ADF).

4) Remove the small cover.

5) Disconnect the ground cable of the ADF harness (Only for the ADF

equipped).

6)Remove the ADF harness (Only for the ADF equipped).

7) Remove ther reader rear cover.

8) Remove the scanner motor.

- Connector [2] 1 pc.

- Screw [3] 2 pcs.

- Spring [4] 1 pc.

F-4-48

4.4.4 Contact sensor

4.4.4.1 Removing the Contact Image Sensor (CIS)

0020-4393

1) Remove the rear cover.

2) Remove the left cover (rear).

3) Remove the copyboard cover (When the ADF is equipped, open the

ADF).

4) Remove the small cover.

5) Disconnect the ground cable of the ADF harness (Only for the ADF

equipped).

6)Remove the ADF harness (Only for the ADF equipped).

7) Remove ther reader rear cover.

8) Remove the copyboard glass.

9) Pull the drive belt (front) [1] in the direction of the arrow to move the con-

tact sensor [2] to the position shown below.

F-4-49

10) Remove the rear side of the contact sensor [1] from the carriage.

11) Disconnect the flexible cable [2], and then remove the contact sensor [1]. 

F-4-50

F-4-51

4.4.4.2 Procedure after Replacing the CIS

0020-4395

After replacing the contact image sensor (CIS), go through the following

steps to perform inter-channel output correction:

1) Enter the service mode.

Sequentially press the Additional Functions, # key on the operation panel.

2) Using the upper/lower arrow keys on the operation panel, select "Test".

3) Press the OK key. 

4) Using the upper/lower arrow keys on the operation panel, select "Scanner

test".

5) Press the OK key.

6) Using the upper/lower arrow keys on the operation panel, select "CS Out-

put Test".

7) Press the OK key.

8) Select "Yes" and then press the OK key.

After completion of the above steps, contact sensor output correction will be

performed and parameters will be set automatically.

MEMO:

Illustrations of this procedure are figured the document size sensor equipped 
model, but procedure is same as document size sensors are not equipped 
model.

[2]

[1]

[2]

[1]

[3]

[4]

[3]

When removing or installing the contact sensor unit, take care not to touch 
the light guide and rod lens array.

[1]

[2]

[2]

[1]

Light guide

Rod lens array

Содержание iR2318 series





















































































































































































































































































































Отзывы:

Нет отзывов