Canon iR2318 series Скачать руководство пользователя страница 130 | Manualshive

Страница: 130 / 308

Canon iR2318 series Скачать руководство пользователя страница 130

Chapter 4

4-24

4.4.5 Copyboard Cover Open/Close Sensor

4.4.5.1 Removing the Copyboard Cover Open/Close

Sensor (Front/Rear)

0020-4403

1) Remove the rear cover.

2) Remove the left cover (rear).

3) Remove the copyboard cover (When the ADF is equipped, open the

ADF).

4) Remove the small cover.

5) Disconnect the ground cable of the ADF harness (Only for the ADF

equipped).

6)Remove the ADF harness (Only for the ADF equipped).

7) Remove ther reader rear cover.

8) Disconnect the two connectors [1], and then remove the screw [2].

9) Remove the reusable band [3], and then remove the harness [4] from the

sensor mount.

10) Remove the sensor mount [5].

11) Remove the sensor from the sensor mount.

F-4-52

4.4.6 Contact Sensor HP Sensor

4.4.6.1 Removing the Contact Sensor HP Sensor (When

the ADF is not installed)

0020-4404

1) Remove the copyboard glass cover.

2) Remove the copyboard glass.

3) Pull the drive belt (front) [1] in the direction of the arrow to move he con-

tact sensor [2] to the center.

4) Remove the connector [3], and then remove the contact sensor HP sensor

[4].

F-4-53

4.4.6.2 Removing the Contact Sensor HP Sensor (When

the ADF is installed)

0021-6259

1) Open the ADF.

2) Remove the copyboard glass.

3)Remove the ADF reading glass.

MEMO:

Illustrations of this procedure are figured the document size sensor equipped
model, but procedure is same as document size sensors are not equipped
model.

[1]

[5]

[2]

[3]

[4]

MEMO:

Illustrations of this procedure are figured the document size sensor equipped
model, but procedure is same as document size sensors are not equipped
model.

[4]

[1]

[2]

[3]

«
...
128
129
130
131
132
...
»

Содержание iR2318 series





















































































































































































































































































































Отзывы:

Нет отзывов