Canon iR2318 series Скачать руководство пользователя страница 110

Страница: 110 / 308

Chapter 4

4-4

Major components of the original exposure system are as follows:

F-4-2

4.1.5 Control System Configuration (When the original size detection sensor is equipped for BOOK mode)

0020-4223

Component

No.

Function/Specification

[1]

Copyboard cover open/close sensor (Rear:
SR402)

SR402

Photo interrupter: Detects the copyboard cover
open/close status. Starts detecting the original
size when the copyboard cover angle is 30 deg.

[2]

Reader controller PCB

Controls drive of the reader unit and image
processing.

[3]

Reader motor

M401

Pulse motor: Controls drive of the carriage.

[4]

Reader heater*1

Prevents condensation inside the original glass.

[5]

Contact image sensor (CIS)

Uses LEDs for indirect exposure (LED +
Photoconductor)

[6]

CISHP sensor

SR401

Photo interrupter: Detects the CIS position.

[7]

Copyboard cover open/close sensor

SR403

Finishes detecting the original size when the
copyboard cover angle is 5 deg.

*1 Option setting

[3]

[2]

[1]

[7]

[4]

[6]

[5]

Содержание iR2318 series





















































































































































































































































































































Результаты поиска

Содержание iR2318 series

Отзывы:

Canon iR2318 series, Руководство по обслуживанию, Страница: 110 / 308

Результаты поиска

Содержание iR2318 series

Отзывы: