Canon iR2318 series Скачать руководство пользователя страница 219

Страница: 219 / 308

Chapter 9

9-9

9.4.2 Main Drive Assembly

9.4.2.1 Removing the Main Drive Unit

0020-4469

1) Open the front cover.

2) Turn the developing assembly locking lever clockwise to open the left

door.

3) Draw out the drum unit.

4) Remove the rear cover.

5) Remove the left cover (rear).

6) Remove the main motor.

7) Remove the registration clutch.

8) Open the left door fully.

9) Remove the gear unit [1] and gear [2].

- E-ring [3] 1 pc.

F-9-19

10) Pull out the handle [1] at the back of the machine, remove the screw [2],

and then remove the stopper [3].

F-9-20

11) Remove the harness [1] from the wire saddle [2].

- Connectors [3] 2 pcs.

F-9-21

12) Remove the handle unit [1].

- Screws [2] 3 pcs.

F-9-22

13) Release the gear stopper [1] from the shaft, and then remove the gear [2].

F-9-23

14) Remove the main drive unit [1].

- Screws [2] 6 pcs.

F-9-24

[3]

[2]

[1]

[2]

[1]

[3]

[2]

[1]

[2]

[1]

[2]

[1]

[2]

[1]

[2]

Содержание iR2318 series





















































































































































































































































































































Результаты поиска

Содержание iR2318 series

Отзывы:

Canon iR2318 series, Руководство по обслуживанию, Страница: 219 / 308

Результаты поиска

Содержание iR2318 series

Отзывы: