Canon iR2318 series Скачать руководство пользователя страница 76

Страница: 76 / 308

Chapter 2

2-22

1) Install the heater PCB unit [2].

- Supplied TP screws (M3x8) [1], 2pcs.

2) Install the heater switch [3] on the right side panel.

F-2-49

3) Install the edge saddle [3]. Connect one heater switch harness [1] to the

connector (J1901) on the heater PCB. Route the other harness [2] to the

front of the host machine through the edge saddle [3].

F-2-50

4) Attach the edge saddle [2], then connect the header switch harness [1]

(routed to the front of the host machine) to the connector (J15) on the

power supply PCB through the edge saddle [2].

F-2-51

5) Install the three clamps [1] on the back of the host machine.

6) Connect the cassette heater harness [2] to the connector (J1905) on the

heater PCB unit, install the reuse band [3], and then pass the harness

through the clamps installed in step 5).

F-2-52

Install the heater switch with the OFF position on the left
and the ON position on the right just like the main power
switch.

[2]

[1]

[3]

[1]

[2]

[3]

[2]

[1]

[3]

[2]

[1]

Содержание iR2318 series





















































































































































































































































































































Результаты поиска

Содержание iR2318 series

Отзывы:

Canon iR2318 series, Руководство по обслуживанию, Страница: 76 / 308

Результаты поиска

Содержание iR2318 series

Отзывы: