Canon iR2318 series Скачать руководство пользователя страница 117 | Manualshive

Страница: 117 / 308

Canon iR2318 series Скачать руководство пользователя страница 117

Chapter 4

4-11

The reader motor driver controls rotation/stop and rotational direction/speed of the reader motor based on the signals from IC2.

F-4-12

a. Forward Movement during Image Scan

During image scan, operation of the contact image sensor (CIS) is controlled by controlling the motor as shown below.

F-4-13

b. Backward Movement after Image Scan

After image scan, the carriage moves back to the contact image sensor (CIS) shading position at the constant speed (118 mm/sec).

4.3.2 Contact Image Sensor (CIS)

4.3.2.1 Outline

0020-4233

Reader controller PCB

3.3V

+24V

RTP3APWN

RTP3BPWN

RTP3A

RTP3B

MO_STANDBY

MO_TORQUE

+5V

J409

B*

B

A

A*

IC2

Motor
driver

1

2

3

4

M401

Start

position

Acceleration

Leading edge

of original

Constant speed

Trailing edge

of original

Stop

Movement

speed

Movement distance

[1]

[2]

[3]

[4]

[1] Acceleration area: The motor accelerates to the speed specified for each mode.
[2] Runup area: A margin to stabilize the speed.
[3] Image read area: The image is read at a constant speed.
[4] Deceleration area: Upon detection of the trailing edge, the motor decelerates rapidly and stops.

Deceleration

«
...
115
116
117
118
119
...
»

Содержание iR2318 series





















































































































































































































































































































Отзывы:

Нет отзывов