Canon iR2318 series Скачать руководство пользователя страница 70

Страница: 70 / 308

Chapter 2

2-16

2.2.4 Setting the Cassettes

0020-4258

1) Holding the knob [1] at the center of the cassette, draw out the cassette [2]

until it stops.

F-2-31

2) Remove the wire [1] securing the inner plate of the cassette.

F-2-32

3) Press the "PUSH DOWN" mark [1] on the inner plate to lock it into the

cassette.

F-2-33

4) Turn the lever [1] of the paper front guide counterclockwise to release it.

Slide the paper front guide [2] to fit to the size of the paper to be used, and

then turn the lever clockwise to lock it.

F-2-34

5) Turn the paper trailing edge registration plate [1] to the left to remove it.

Re-attach it to fit to the size of the paper to be loaded.

F-2-35

6) Slide the paper size detection lever [1] to fit to the paper size.

F-2-36

[1]

[2]

[1]

PUSH DOWN

[1]

LTR

STMT

11 17

LTR

LGL

[1]

[2]

[1]

Содержание iR2318 series





















































































































































































































































































































Результаты поиска

Содержание iR2318 series

Отзывы:

Canon iR2318 series, Руководство по обслуживанию, Страница: 70 / 308

Результаты поиска

Содержание iR2318 series

Отзывы: