Canon iR2318 series Скачать руководство пользователя страница 218

Страница: 218 / 308

Chapter 9

9-8

9.4.1.6 Left Cover (Rear)

9.4.1.6.1 Removing the Left Cover (Rear)

0020-4465

1) Detach the rear left cover [1].

- Screws [2] 3 pcs.

F-9-14

9.4.1.7 Reader Front Cover

9.4.1.7.1 Removing the Reader Front Cover

0020-4467

1) Open the copyboard cover (or ADF).

2) Detach the reader front cover [1].

- Screws [2] 2 pcs.

F-9-15

9.4.1.8 Reader Rear Cover

9.4.1.8.1 Removing the Reader Rear Cover

0020-4468

1) Remove the rear cover.

2) Open the front cover.

3) Remove the right cover (lower).

4) Remove the right cover (upper).

5) Remove the left cover (rear).

6) Open the copyboard cover (or ADF).

7) Remove the small cover [1].

- Screw [2] 1 pc.

F-9-16

8) Disconnect the ground cable [1] of the ADF harness (Only for ADF

equipped).

- Screw [2] 1 pc.

9) Remove the ADF harness [3] (Only for ADF equipped).

- Connectors [4] 4 pcs.

F-9-17

10) Remove the reader rear cover [1].

- Screws [2] 4 pcs.

F-9-18

[1]

[2]

[1]

When installing the ADF harness [3], fit the harness band [5] in the groove
in the reader rear cover.

[1]

[2]

[1]

[4]

[3]

[5]

[2]

[1]

Содержание iR2318 series





















































































































































































































































































































Результаты поиска

Содержание iR2318 series

Отзывы:

Canon iR2318 series, Руководство по обслуживанию, Страница: 218 / 308

Результаты поиска

Содержание iR2318 series

Отзывы: