Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 93

Страница: 93 / 270

Chapter 5

5-3

5.2 Parts Replacement Procedure

5.2.1 Laser Scanner Unit

5.2.1.1 Removing the Laser Scanner Unit

0013-1216

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

The laser scanner was-factory adjusted. Never disassemble it.

1) Detach the reader left cover, left front cover, internal cover, and delivery

tray front cover.

2) Detach the right cover, control panel, and delivery tray.

3) Remove the laser shutter [1].

4) Disconnect the connector [2] and flexible cable [3].

5) Remove the four screws [4] using a stubby screwdriver, and then remove

the laser scanner unit [5].

F-5-2

MEMO:

When reinstalling the laser scanner unit, it is difficult to install the encircled

screw if your stubby screw driver is not magnetized. In this case, first install

the screw in the screw hole on the laser scanner unit, place the laser scanner

unit in place, and then tighten the screw tightly.

F-5-3

[3]

[4]

[1]

[2]

[5]

Содержание ImageRUNNER 1022iF















































































































































































































































































Результаты поиска

Содержание ImageRUNNER 1022iF

Отзывы:

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 93 / 270

Результаты поиска

Содержание ImageRUNNER 1022iF

Отзывы: