Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 221 / 270

Chapter 15
15-15
Use it to set the pattern of the pseudo RBT signal transmitted at time of a fax/tel switchover.
15.5.11 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022:
pseudo CI signal pattern OFF time length (long)>
0013-1350
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to set the pseudo CI signal pattern transmitted at time of a fax/tel switchover.
15.5.12 <023: CNG detention level for fax/tel switchover>
0013-1351
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to set the CNG detention level for a fax/tel switchover.
15.5.13 <024: pseudo RBT transmission level at time of fax/tel switchover>
0013-1352
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to set the pseudo transmission level for a fax/tel switchover.
15.5.14 <025: Answering machine connection function signal detection time>
0013-1353
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Sets the signal detection time for the answering machine connection function operation. When the answering machine connection function is operating, if the func-
tion does not operate normally because the fax does not detect CNG signal sent from the line, raise this parameter to increase the signal detection time.
15.5.15 <027: V.21 low-speed flag preamble identification length>
0013-1354
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to detect the time of detection after which command analysis is started after detecting V.21 low-speed command preambles continuously for a specific period
of time.
15.5.16 <056 - 061: Count type select >
0013-7933
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to confirm the count type indicated on the Counter Check screen, which appears in response to a press on the Counter key.
When '0' is selected, count type will not be indicated.
No.56: Use it to change the type of soft counter 1* of the control panel to suit the needs of the user.
No.57: Use it to change the type of soft counter 2* of the control panel to suit the needs of the user.
No.58: Use it to change the type of soft counter 3* of the control panel to suit the needs of the user.
No.59: Use it to change the type of soft counter 4* of the control panel to suit the needs of the user.
No.60: Use it to change the type of soft counter 5* of the control panel to suit the needs of the user.
No.61: Use it to change the type of soft counter 6* of the control panel to suit the needs of the user.
*:The default type settings of soft counter is different from models.
<Soft Counter Specifications>
The soft counters are classified a follows in terms of input numbers:
100s: total
200s: copy
300s: print
400s: copy + print
500s: scan
700s: received file print
800s: report pint
900s: transmitted scan
Guide to the Table
- 1:Count sheets of all sizes by one.
- 2:Count sheets of the large size by two.
- C:full color
- Bk:black mono
- L:large size (larger than A4/LTR)
- S:small size (A4/LTR or smaller)
MEMO:
To make a change so that B4 papers (for print) will be counted as large-size, use service mode: make the following selections, and change bit 0 to '1': #SSSW>SW33.
To make a change so that B4 papers (for scan) will be counted as large-size, use service mode: make the following selections, and change bit 2 to '1': #SSSW>SW33.
Seri
al
No.
on
cou
nter
chec
k
scre
en Counter type Print system
Bk 1-sided L
Bk 1-sided S Bk 2-sided L Bk 2-sided S
Local
copy PDL
print FAX
print Repo
rt
print Local
copy PDL
print FAX
print Repo
rt
print Local
copy PDL
print FAX
print Repo
rt
print Local
copy PDL
print FAX
print Repo
rt
print
101 Total1 1 1 1 1 1 1 1 1
102 Total2 2 2 2 2 1 1 1 1
103 Total (L) 1 1 1 1
104 Total (S) 1 1 1 1
108 Total (Bk1) 1 1 1 1 1 1 1 1
109 Total (Bk2) 2 2 2 2 1 1 1 1
112 Total (Bk/L) 1 1 1 1