Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 147

Страница: 147 / 270

Chapter 9

9-11

F-9-30

When mounting the screw surrounded with a circle, mount it with a

grounded plate spring.

9.4.9 Network PCB

9.4.9.1 Removing the Network PCB

0013-2027

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

1) Detach the rear cover.

2) Disconnect the connector [1], and then release the cable from the cable

clamp.

3) Remove the three screws [2], and then remove the LAN cover [3].

F-9-31

4) Disconnect all connectors from the network PCB.

5) Remove the four screws [1], and then remove the network PCB [2].

F-9-32

9.4.10 Relay PCB

9.4.10.1 Removing the Relay PCB

0013-2024

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

1) Detach the rear cover.

2) Disconnect all connectors from the relay PCB.

3) Remove the two screws [1] and relay PCB [2].

F-9-33

9.4.11 Interlock Switch

9.4.11.1 Removing the Interlock Switch

0013-2031

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

1) Detach the reader left and the front-left cover.

2) Detach the rear cover, the right cover, the inner cover, the control panel

and the delivery tray.

3) Disconnect the connector (J112) from the DC controller PCB, and then

remove the cable from the cable guide by cutting cable ties.

4) Release the two claws [1], and then remove the interlock switch (for front

cover) [2].

F-9-34

5) Remove the screw [1], and then detach the cable guide [2].

6) Release the two claws [3], and then remove the interlock switch (for left

door) [4].

F-9-35

9.4.12 Fans

9.4.12.1 Removing the Heat Discharge Fan

0013-2003

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

1) Detach the rear cover and rear-left cover.

2) Disconnect the connector [1], release the two hooks [2], and then remove

the heat discharge fan [3].

[1]

[2]

[1]

[2]

[1]

[2]

[3]

[1]

[2]

[1]

[2]

[1]

[2]

[4]

[3]

Содержание ImageRUNNER 1022iF















































































































































































































































































Результаты поиска

Содержание ImageRUNNER 1022iF

Отзывы:

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 147 / 270

Результаты поиска

Содержание ImageRUNNER 1022iF

Отзывы: