manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 108 / 270

Поделиться
Скачать
Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 108

Chapter 7  

7-2

7.2 Detecting Jams

7.2.1 Jam Detection Outline

7.2.1.1 Outline

0013-1106

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

The machine is equipped with 3 jam sensors and 1 jam switch used to motor the movement of paper. 

The presence/absence of paper or of a jam is checked at such times as programmed in advance in the CPU of the DC controller PCB and in relation to the presence/

absence of paper over a specific sensor at a given time. If the machine detects a jam, it will turn off the main

motor (M1), and will indicate a jam message in the control panel.

F-7-2
T-7-2

7.2.1.2 Types of Jams

0013-1107

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

The machine groups jams into 7 types. When a jam occurs, be sure to remove it, and start over the operation.

Pickup Delay Jam

After execution of a pickup retry, the registration sensor (SR11) does not detect the leading edge of paper within a specific period of time. Or after the duplex drive

solenoid (SL1) is on, the registration sensor (SR11) does not detect the leading edge of paper within a specific period of time.

Delivery Sensor Delay Jam

After the registration sensor (SR11) has detected the leading edge of paper, the delivery sensor (SR5) does not detect the leading edge of paper within a specific

period of time.

Pickup Stationary Jam

After the registration sensor (SR11) has detected the leading edge of paper, the registration sensor (SR11) does not detect the trailing edge of paper within a specific

period of time.

Delivery Sensor Stationary Jam

After the registration sensor (SR11) has detected the trailing edge of paper, the delivery sensor (SR5) does not detect the trailing edge of paper within a specific

period of time.

Wound Paper Jam at Fuser

The delivery sensor (SR5) has detected absence of paper within the prescribed time after it detected presence of paper.

Initial Jam

- When presence of paper is detected by the registration sensor (SR11) or delivery sensor (SR5) at the start of waiting.

- When presence of paper is detected by the delivery sensor (SR5) during waiting.

Left door/Front Cover Open Jam

During paper feeding, the interlock switch (SW2/SW3) has detected OFF.

Symbol

Name

SR5

Delivey sensor

SR9

Cassette paper sensor

SR11

Registration sensor

SW2/SW3

Interlock switch

SR9

SR11

SW2

SR5

SW3

Содержание ImageRUNNER 1022iF















































































































































































































































































Отзывы:

Нет отзывов