Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 179

Страница: 179 / 270

Chapter 12

12-3

12.4 ADF

12.4.1 Outline

12.4.1.1 Outline

0013-1273

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

This machine has the following adjustment items. Make the necessary ad-

justments after replacing each part.

T-12-3

12.4.1.2 Preparing a Test Sheet for Adjustment

0013-1274

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

Preparing a Test Sheet: On a sheet of A4 or LTR paper, draw straight lines

as indicated:

F-12-7

F-12-8

12.4.2 Adjusting the Mechanical System

12.4.2.1 Adjusting the Perpendicularity

0013-1276

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

1) reate a test chart, load it in the ADF, and make a copy of it.

2) Compare the lines at the end of the test chart with those on the copy for

perpendicularity. Measure dimensions A and B at the end of the copy and

adjust the amount of skew (the range shown in the table) to within the

spec.

T-12-4

F-12-9

3) Loosen the two screws [1] securing the right hinge and slide the hinge

according to the sale markings so that the perpendicularity is within spec.

F-12-10

4) Tighten the screws you loosened in step 3.

12.4.3 Adjusting the Ellectrical System

12.4.3.1 Adjusting the Magnification

0013-1277

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

1) Create a test chart, load it in the ADF, and make a copy of it. This copy is

called copy A.

2) Compare the longitudinal image length on the test chart with that on copy

A. If required, make an adjustment in the service mode.

(A4-size paper: 277 +/-1mm LTR paper: 59 +/-1mm)

Image on copy A is shorter. -> Increase the value (or reduce the stream read-

ing speed).

Image on copy A is longer. -> Decrease the value (or increase the stream

reading speed).

3) Enter the service mode.

Sequentially press the additional functions key, 2 key, 8 key, and additional

functions key on the operation panel of the host machine.

4) Using the arrow keys on the operation panel, display "#SCAN".

5) Press the OK key.

6) Using the arrow keys on the operation panel, display "#SCAN

NUMERIC".

7) Press the OK key.

8) Using the arrow keys, select "48".

9) Using the numeric keys, change the value to determine the optimum value.

Next, press the OK key. (Default: 32)

Do not change the adjustment value excessively.

12.4.3.2 Adjusting the Horizontal Registration

0013-1279

/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /

1) Load the test chart in the ADF and make a copy of it.

2) Compare the horizontal registration of the chart with that of the copy. If

required, make an adjustment.

The specified horizontal registration is 10mm +/-2mm.

No.

Adjustment type

Replaced parts

[1]

Perpendicularity adjustment Hinge

[2]

Magnification adjustment

Motor/roller

[3]

Side registration adjustment -

[4]

Leading edge registration
adjustment

Dimension
(using A4)

Dimension
(using LTR)

A-B

0 +/- 1.5 mm

10mm

Draw straight lines.

(feeding direction)

10mm

210mm

297mm

10mm

Draw straight lines.

(feeding direction)

10mm

216mm

279mm

Copy of the test sheet

(feeding direction)

[1]

Содержание ImageRUNNER 1022iF















































































































































































































































































Результаты поиска

Содержание ImageRUNNER 1022iF

Отзывы:

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 179 / 270

Результаты поиска

Содержание ImageRUNNER 1022iF

Отзывы: