manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 146 / 270

Поделиться
Скачать
Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 146

Chapter 9  

9-10

F-9-26

9.4.5.2 Procedure after Replacing the Image Processor 

PCB

0013-1991

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

If you have replaced the image processor PCB with a new one, perform the

following operations: 

- Attach altogether the PCB on the old image processor PCB in the new im-

age processor PCB.

- Using the service support tool, download the latest firmware (System/Boot/

PCL*1) and language files.

*1: if equipped with PCL functions  

- Input the all value printed on the service label affixed to the rear cover.

Make the following adjustments:

- Correction of output between CS channels 

1) Enter the service mode.

Sequentially press the Additional functions key, 2 key, 8 key, and Additional

functions key on the operation panel.

2) Press the arrow key on the touch panel to display "TEST MODE".

3) Press [OK].

4) Press the [2] key to display "SCAN TEST".

5) Press the [1] key to display "SHADING".

6) Press [OK].

After completion of the above procedure, the contact sensor output is com-

pensated and parameters are set automatically.  

After completion of automatic adjustment, "OK" is displayed.

- Read position adjustment (Stream reading: Only when the ADF is installed)

1) Enter the service mode.

Sequentially press the Additional functions key, 2 key, 8 key, and Additional

functions key on the operation panel.

2) Press the arrow key on the touch panel to display "TEST MODE".

3) Press [OK].

4) Press the [2] key to display "SCAN TEST".

5) Press the [3] key to display "SHEET POS ADJ".

6) Press [OK].

The optical system starts scanning. Several seconds later, automatic adjust-

ment of the reading position finishes and "OK" appears.

If automatic adjustment fails, "NG" appears. Perform the following

procedure:

Clean the platen guide of the ADF and the document glass of the host ma-

chine, and then retry auto adjustment. 

9.4.6 NCU PCB

9.4.6.1 Removing the NCU PCB

0013-1997

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Detach the rear cover.

2) Remove all connectors and flexible cables from the NCU PCB.

3) Remove the two screws [1], and then remove the NCU PCB [2].

F-9-27

9.4.7 Modular Jack PCB

9.4.7.1 Removing the Modular Jack PCB

0013-2000

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Detach the rear cover.

2) Disconnect all connectors from the modular jack PCB.

3) Remove the two screws [1], and then remove the modular jack PCB [2].

F-9-28

9.4.8 Modem PCB

9.4.8.1 Removing the Modem PCB

0013-2026

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Detach the rear cover.

2) Disconnect the connector [1], and then release the cable from the clamp.

3) Remove the three screws [2], and then remove the LAN cover [3].

F-9-29

4) Disconnect all connectors from the modem PCB.

5) Remove the three screws [1], and then remove the modem PCB [2].

[1]

[1]

[1]

[2]

[1]

[2]

[1]

[2]

[1]

[2]

[1]

[2]

[3]

Содержание ImageRUNNER 1022iF















































































































































































































































































Отзывы:

Нет отзывов