manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 253 / 270

Поделиться
Скачать
Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 253

Chapter 16

16-1

16.1 Outline

16.1.1 Overview of Upgrade

0013-1286

iR1018

This machine and options can be upgraded by downloading system software programs from the personal computer (hereafter called as the PC) in which a service

support tool (hereafter called SST) has been loaded.

System software programs and upgrade tools are listed in the following table:

T-16-1

Download the system software for PCL board following the same procedure described in "Downloading the System".

When updating the version of Boot (boot program) and System (main controller) at the same time, make sure to first update Boot. If you start by updating System,

the unit may not start up.

16.1.2 Overview of Service Support Tool

0013-1287

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

F-16-1

When using the SST, select "#DOWNLOAD" in the service mode to place the main unit in the download mode. 

16.2 Making Preparations

16.2.1 Registering the System Software

0013-1288

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

System software programs to be downloaded need to be registered in the SST.

The system software programs are registered with the names listed below.

<Software Programs Preinstalled in Main Unit>

T-16-2

Use the firmware for the model suitable for the compatible product.

Unit name:

- Main controller: System

- Boot program: Boot

- PCL board: PCL

The system software registration program is explained below taking Boot as an example.  

[Preparation]

Have the following ready: 

- PC in which SSTv3.21 or later is installed

- System CD containing the firmware for the relevant model

Type

System software type

Upgrade tool

Remarks

SST

Main unit

Boot (boot program)

Yes

Main controller also controls the 
reader.

System (main controller)

Yes

PCL

Yes

16MB ROM PCB

Display name

Compatible product name

Remarks

iR1018J

iR1018J, iR1019J , iR1022J

Flash ROM 12MB type

iR1022

iR1018, iR1022, iR1022A, iR1022F, iR1022i, iR1022iF, iR1023, iR1023iF, iR1023N

Flash ROM 16MB type

CPU

USB cable

Image processor PCB

PCL ROM

Main unit

PC

J303

Flash ROM

Flash ROM

System 
software

SST

Содержание ImageRUNNER 1022iF















































































































































































































































































Отзывы:

Нет отзывов