manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 159 / 270

Поделиться
Скачать
Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 159

Chapter 10

10-7

10.3 Detection Jams

10.3.1 Outline

0013-1198

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

This machine detects a jam using the sensors shown below. Document jam check timings are stored in the ROM on the image processor PCB to check whether a

jam has occurred according to presence/absence of the document at the relevant sensor position.

When a jam occurs, the host machine stores its code.

Jam codes can be checked by outputting a jam error log report in the service mode of the host machine.

F-10-11

T-10-4

T-10-5

SR2001: Document set sensor
SR2002: Document edge sensor
SR2003: Registration sensor
SR2004: Separation rear sensor

Code

Name

Sensor No.

Description

0000

Unknown jam

-

Other errors

0007

Initial stationary

SR2002, R2003, SR2004

Paper is detected in the transport path before the ADF starts initial operation.  

0008

Document edge sensor delay SR2002

The document edge sensor does not detect paper when the paper has been fed by the 
predetermined distance since reception of a pickup request. 

0009

Document edge sensor 
stationary

SR2002

The trailing edge of paper is not detected when the paper has been fed by the 
predetermined distance since detection of it by the docement edge sensor.  

000a

Paper absence (Pull out the 
document.)

SR2001

The document set sensor has been held off since start of pickup. 

000c

Delievery delay

SR2002

In case the internal software signal "Delivery Sensor ON" set in the system cannot 
be detected, when the paper feed request is received and the paper is fed the 
prescribed distance, and the leading edge of paper is detected and paper is fed the 
prescribed distance . 

000d

Delievery stationary

SR2002

In case the internal software signal "Delivery Sensor OFF" set in the system cannot 
be detected, when the leading edge of paper is detected by the document edge sensor 
and fed the prescribed distance, and after the paper's trailing edge is detected.  

0010

Pickup NG

SR2003

The registration sensor has been held off since paper pickup started.

SR2003

SR2002

SR2004

SR2001

Содержание ImageRUNNER 1022iF















































































































































































































































































Отзывы:

Нет отзывов