
Chapter 15
15-9
T-15-3
15.3.4.2 Detailed Discussions of Bit 2
0013-1310
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to select the number of last flag sequences for a protocol signal (transmission speed at 300 bps). Select '2' if the other party fails to receive the protocol signal
properly.
Memo:
Any of the following error codes may be indicated at time of transmission
##0100, ##0280, ##0281, ##0750, ##0753, ##0754, ##0755, ##0758, ##0759, ##0760, ##0763 ##0764, ##0765, ##0768, ##0769,##0770, ##0773, ##0775, ##0778,
##0780, ##0783, ##0785, ##0788
15.3.4.3 Detailed Discussions of Bit 3
0013-1311
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to select an appropriate reception mode after transmission of the CFR signal.
If errors occur frequently at time of reception because of the condition of the line, select 'high speed' for reception mode and, at the same time, selects 'do not receive'
for 'ECM reception.'
Memo:
Any of the following error codes may be indicated at time of reception because of line condition
##0107, ##0114, ##0201
Be sure to change bit 4 before changing this bit; if errors still occur, change this bit.
When 'high speed' is selected, only high-speed signals (images) will be received after transmission of the CFR signal.
15.3.4.4 Detailed Discussions of Bit 4
0013-1312
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to select the time length during which low-speed signals are ignored after transmission of the CFR signal.
If the condition of the line is not good and, therefore, the reception of image signals is difficult, select '1500 ms.'
15.3.4.5 Detailed Discussions of Bit 6
0013-1313
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Selects whether or not to transmit CNG signal during manual transmission.
In manual transmitting to a fax with the FAX/TEL switching mode, if there are frequent errors due to failure to switch to fax mode, select "Transmitted" for the
CNG signal.
15.3.4.6 Detailed Discussions of Bit 7
0013-1314
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Selects whether or not to transmit CED signals during manual reception. If the other fax does not transmit even when you start manual reception, select "Transmit-
ted" for the CED signal.
15.3.5 SSSW-SW05
15.3.5.1 List of Functions
0013-1315
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
T-15-4
15.3.5.2 Detailed Discussions of Bit 1
0013-1316
/ / / / iR1018 / iR1018J / / iR1022A / iR1022F / iR1022i / iR1022iF /
Use it to enable/disable millimeter/inch conversion in sub scanning direction for images read in text mode.
Scanning direction in conversion follows the Bit 2 setting of SW14.
Bit
Function
1
0
0
not used
-
-
1
not used
-
-
2
the number of final flag sequences of protocol signals
2
1
3
Reception mode after CFR signal transmission
high speed
high speed/low speed
4
the length of the period of ignoring low speed signals after
CFR output
1500 ms
700 ms
5
not used
-
-
6
CNG signal for manual transmission
Not transmitted
Transmitted
7
CED signal for manual reception
Not transmitted
Transmitted
Bit
Function
1
0
0
not used
-
-
1
Conversion from mm to inch (text mode)
convert
do not convert
2
Conversion from mm to inch (text/photo mode)
convert
do not convert
3
not used
-
-
4
not used
-
-
5
not used
-
-
6
not used
-
-
7
not used
-
-
Содержание ImageRUNNER 1022iF
