manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 244 / 270

Поделиться
Скачать
Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 244

Chapter 15  

15-38

F-15-17

6-3:SENOR
[1] - [8]

SENSOR CHECK
0:NORMAL 1:LATCH

SWITCH CHECK
[0] - [1]

DS ON DES of HPS ON
BCVS of

Press numeric keypad key 1.

SENSOR NORMAL
[0] - [2]

Press numeric keypad key 0.

Select a sensor mode.
 0: NORMAL
 Indications change from 0 
 to 1 as the sensors turn on.
 Indications change from 1 
 to 0 as the sensors turn off.
 1: LATCH
 Indications change from 0 
 to 1 as the sensors turn on.
 Indications do not change back
 from 1 to 0 once the sensors turn
 on from the off state.

CAS:Cassette paper sensor (SR9): 0/Document presence, 1/Document absence 
REG:Registration sensor (SR11): 0/Document presence, 1/Document absence
DEL 0 0:
               Delivery sensor (SR5): 1/ Document presence, 0/ Document absence
               Not used
MULTI:Manual paper sensor (SR12): 0/Document presence, 1/Document absence

SENSOR LATCH
[0] - [2]

Press numeric keypad key 1.

CAS 0000
LOCK 0

Press numeric keypad key 0.

OP1 0000

OP2 0000

OP3 0000

Press numeric keypad key 1.

CAS 0

REG 0

DEL 0 0

MULTI 0

Press numeric keypad key 0.

TONER: Waste toner full detection sensor (SR6)

: 0/Document presence, 1/Document absence

FULL: Delivery

 full sensor (SR10): 0/Document presence, 1/Document absence

2ND-DEL 0 0:
           

  

Not used

            

  

Not used

            

TONER 0

FULL 0

2ND-DEL 0 0

Press numeric keypad key 1.

OP1 0 0:

                  Not used

                Option casstte paper

 sensor (SR6)

                 : 0/Document presence, 1/Document absence

OP2 0 0: 

Not used

 

OP3 0 0: 

Not used

PATH 0 0: 

Not used

OP1 0 0

OP2 0 0 

OP3 0 0

PATH 0 0

Press numeric keypad key 2.

Press numeric keypad key 2

Press numeric keypad key 3

DS: ADF original set sensor (SR2001): 

On/Paper presence, Of/Paper absence

DES: ADF document edge snsor (SR2002): 

On/Paper presence, Of/Paper absence

HP: CS HP sensor (SR401): 

On/Paper presence, Of/Paper absence

BCVS: Not used

OP1: Not used
OP2: Not used
OP3: Not used

CAS 0000: Not used
LOCK 0: Not used

Содержание ImageRUNNER 1022iF















































































































































































































































































Отзывы:

Нет отзывов