manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 231 / 270

Поделиться
Скачать
Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 231

Chapter 15

15-25

15.8 Registration of Accessories (ACC)

15.8.1 Accessory Registration

0013-7948

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

The table below gives summary description of the accessories available.

15.9 Display of Counter Information (COUNTER)

15.9.1 Counters

0013-1409

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

This copier is furnished with a maintenance/supplies counter set (DRBL-1), which can be used to gain rough measures of when to replace supplies.  The counter

set increments by one on counting each sheet of small-sized paper (up to A4/LTR) and by two on counting each sheet of large-sized paper (larger than A4/LTR).

T-15-20

T-15-21

15.9.2 Clearing Counters

0013-1410

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

Item

Explanation

#ACC

CARD

Card reader installation setting
Enter a card number to use.
(0 to 9999.  One hundred cards are registered with the department ID beginning from the input card number in sequence.)
*1:1,000 cards if option ROM is mounted.
When a card number is entered, the following kinds of management information are initialized:
- Card name (department ID), beginning from the input card number.
- Password associated with the card

CC-SPSW

Control card I/F support setting
Set whether to support the control card I/F (CC-V) or not.
0: Do not support.
1: Support.

COIN

Coin vendor change
Set the control card set display appearing on the operator station for vendor use.
0: Control card use
1: Coin vendor use

CONTROL

Set the PDL printer output control where the control card I/F (CC-V) is supported.
0: Enable printing without a card mounted.
1: Enable printing with a card mounted in position.

Maintenance counter list
Item

Counter

Explanation

TOTAL (Total counter)

SERVICE1

Service total counter 1

SERVICE2

Service total counter 2

TTL

Total counter

COPY

Total copy counter

PDL-PRT

PDL print counter

FAX-PRT

Fax print counter

REP-PRT

Report print counter

2-SIDE Double-sided 

copy/print 

counter

SCAN

Scan counter

PICK-UP (Paper pickup counter)

C1

Cassette 1 jam counter

C2

Cassette 2 jam counter

C3

Not used

C4

Not used

MF

Manual feed tray pickup total counter

2-SIDE

Double-sided paper pickup total counter

FEEDER (Feeder related counters)

FEED

Feeder pickup total counter

DFOP-CNT

ADF open/close hinge counter

JAM (Jam counters)

TTL

Unit total jam count

FEEDER

Feeder total jam count

SORTER

Not used

2-SIDE

Duplex unit jam counter

MF

Manual feed tray jam counter

C1

Cassette 1 jam counter

C2

Cassette 2 jam counter

C3

Not used

C4

Not used

MISC (Other required counter)

WST-TNR

Not used

Parts counter list
Item

Counter

Explanation

Service life

DRBL-1 (Unit supplies)

PT-DRM

Drum unit rotation count

26,000 

Содержание ImageRUNNER 1022iF















































































































































































































































































Отзывы:

Нет отзывов