manualshive.com logo in svg

Canon ImageRUNNER 1022iF, Руководство по обслуживанию, Страница: 143 / 270

Поделиться
Скачать
Canon ImageRUNNER 1022iF Скачать руководство пользователя страница 143

Chapter 9

9-7

F-9-12

9.4.1.1.9 Detaching the Front Cover

0013-2409

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Remove the cassette.

2) Using a flathead screwdriver, release the two claws [1] at the right and

four hooks [2] at the top.

3) By releasing the two bosses [3] at the bottom, detach the inner cover [4].

F-9-13

9.4.1.1.10 Detaching the Inner Cover

0013-7317

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Detach the toner supply bottle.

2) Remove the two screws [1].

3) Release the two claws [2], and the remove the inner cover [3].

F-9-14

9.4.1.1.11 Detaching the Delivery Tray Front Cover

0013-7319

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Detach the reader left cover, the front-left cover, and the inner cover.

2) Remove the screw [1], and then detach the delivery tray front cover [2].  

F-9-15

9.4.1.1.12 Detaching the Delivery Tray

0013-2411

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Remove the reader left cover and the front-left cover. 

2) Remove the rear cover, the reader rear cover, the right cover, the reader

right cover, the inner cover and the delivery tray front cover. 

3) Detach the operation panel.

4) Detach the delivery tray [1] from the front.

F-9-16

9.4.2 Drive Unit

9.4.2.1 Removing the Main Drive Unit

0013-3169

 /  /  /  / iR1018 / iR1018J /  / iR1022A / iR1022F / iR1022i / iR1022iF / 

1) Remove the rear cover, the reader left cover and the rear-left cover. 

2) Remove the fan duct, the main motor, the relay PCB, the registration

clutch, and the pickup drive unit.

[3]

[4]

[2]

[1]

[3]

[4]

[1]

[2]

[2]

[3]

[1]

[2]

[1]

[1]

Содержание ImageRUNNER 1022iF















































































































































































































































































Отзывы:

Нет отзывов