background image

46

Nominal heat output/Nominal heating  

capacity

The nominal heat output is the heat energy given off per 
unit of time when the fireplace is operated according to 
the specified filling quantities in its work phase. 

Fireplace dependent on room air

A fireplace dependent on room air removes the 

 

combustion air completely or partially from the 

 

installation room.
A fireplace dependent on room air can be equipped with 
a supply line which feeds in the combustion air from 
outdoors. Nevertheless, this variant is considered to 
be dependent on room air, as the fireplace itself does 
not hat the increased leak-tightness to prevent the  
removal of combustion air from the installation room. 
Schmid masonry stoves are fireplaces dependent on 
room air, which are provided with a connection for the 
supply of air from the outside.

Fireplace independent of room air

A fireplace independent of room air does not remove 
the combustion air from the installation room. The 
stove system must meet certain technical conditions 
(leak-tightness) and must be approved for this use.

Return line

The return line is the connection side at which the cooled 
heating water is fed into the boiler from the heating  
circuit.

Self-closing door

A self-closing door falls back into the door frame  
(usually with spring force) without any action by the  
operator. However, in this position, the door is not locked 
or closed and the the door seal does not seal tightly.  
Therefore, these doors must always be locked with  
operating the stove system. 

Safety device

A safety device is a protective system for the 

 

prevention of damage. The function of safety devices 
must be checked regularly. On a heating water circuit, 
e.g. the thermal discharge safety device and the safety 
valve, at least once a year.

Thermal discharge safety device

The thermal discharge safety device is a safety device  
which adds cold drinking water to the system at  
excessively high heating water temperatures 

 

(approx. 97° C). It must never be locked, tampered with  

or deactivated.

Combustion air line

The combustion air line is the component that routes 
the combustion air to the fireplace.

Supply line

The supply line is the connection side at which the  
heated heating water is routed from the boiler back into 
the heating circuit.

Thermal output range

The thermal output range specifies the limits for the 
minimum/maximum thermal output within which the 
fireplace can still be properly operated. This thermal 
output primarily results from the quantity of fuel used 
and the quantity of air provided.

Temporarily burning fireplace

The term temporarily burning fireplace describes (in 
highly simplified terms) that your fireplace requires  
intervention in the combustion process during the  
combustion period. 
For the term continuously burning fireplace may only 
be applied to fireplaces which continue to burn without  
the addition of fuel and without intervention in the  
combustion process for a certain minimum period and 
at a low setting so that the embers (at least as large as 
the basic mass of embers before adding the fuel) can be 
started again at the end of the period. 
All fireplaces operated with a wood fire always require 
intervention in the combustion process, among other 
things to be able to meet the requirements for Germany 
in accordance with the 1st BImSchV and are therefore 
temporarily burning fireplaces.
However, the term temporarily burning fireplace does 
not specify a time restriction for the operating duration. 
Ultimately, the combustion duration is determined by 
the quantity of fuel used and the quantity of air provided. 
If combustion is ended, the next combustion can also be 
started again immediately with the embers. This means, 
your needs determine how long and how often you heat. 

Содержание GO-Line S21

















































Отзывы: