GB
Page 8 / 64
A,AS Rev13 - Operating Instructions
THIS INSTRUCTION MANUAL IS THE PROPERTY
OF CALPEDA S.P.A. ANY REPRODUCTION,
EVEN IF PARTIAL, IS FORBIDDEN
1. GENERAL INFORMATION
Before using the product carefully read the
information contained in this instruction manual, the
manual should be kept for future reference.
Italian is the original language of this instruction
manual, this language is the reference language in
case of discrepancies in the translations.
This manual is part of the essential safety
requirement and must be retained until the product
is finally de-commissioned.
The customer, in case of loss, can request a copy
of the manual by contacting Calpeda S.p.A. or their
agent, specifying the type of product data shown on
the label of the machine (see 2.3 Marking)
Any changes, alterations or modifications made
to the product or part of it, not authorized by the
manufacturer, will revoke the “CE declaration” and
warranty.
1.1. Symbols
To improve the understanding of the manual, below
are indicated the symbols used with the related
meaning.
Information and warnings that must be
observed, otherwise there is a risk that the
machine could damage or compromise
personnel safety.
The failure to observe electrical information
and warnings, could damage the machine or
compromise personnel safety.
i
Notes and warnings for the correct
management of the machine and its parts.
Operations that could be performed by
the final user. After carefully reading of the
instructions, is responsible for maintenance
under normal conditions. They are
authorized to affect standard maintenance
operations.
Operations that must be performed by a
qualified electrician. Specialized technician
authorised to affect all electrical operations
including maintenance. They are able
to operate with in the presence of high
voltages.
Operations that must be done performed by a
qualified technician. Specialized technician
able to install the device, under normal
conditions, working during “maintenance”,
and allowed to do electrical and mechanical
interventions for maintenance. They must
be capable of executing simple electrical
and mechanical operations related to the
maintenance of the device.
Indicates that it is mandatory to use
individual protection devices.
OFF
Operations that must be done with the
device switched off and disconnected from
the power supply.
ON
Operations that must be done with the
device switched on.
1.2. Manufacturer name and address
Manufacturer name: Calpeda S.p.A.
Address: Via Roggia di Mezzo, 39
36050 Montorso Vicentino - Vicenza / Italia
www.calpeda.it
1.3. Authorized operators
The product is intended for use by expert operators
divided into end users and specialized technicians.
(see the symbols above).
i
It’s forbidden, for the end user, carry out
operations which must be done only by
specialized technicians. The manufacturer
declines any liability for damage related to
the non-compliance of this warning.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience
and knowledge, unless they have been given
supervision or instruction concerning use of the
appliance by a person responsible for their safety.
Children should be supervised to ensure that they
do not play with the appliance.
1.4. Warranty
For the product warranty refer to the general terms
and conditions of sale.
i
The warranty covers only the replacement
and the repair of the defective parts of the
goods (recognized by the manufacturer).
The Warranty will not be considered in the following
cases:
- Whenever the use of the device does not conform
to the instructions and information described in this
manual.
- In case of changes or variations made without
authorization of the manufacturer.
- In case of technical interventions executed by a
non-authorized personnel.
- In case of failing to carry out adequate
maintenance.
SUMMARY
1. GENERAL INFORMATION ........................8
2. TECHNICAL DESCRIPTION ......................9
3. TECHNICAL FEATURES ...........................9
4. SAFETY......................................................9
5. TRANSPORTATION AND HANDLING .....10
6. INSTALLATION ........................................10
7. STARTUP AND OPERATION ................... 11
8. MAINTENANCE .......................................12
9. DISPOSAL ................................................12
10. SPARE PARTS .........................................12
11. TROUBLESHOOTING .............................13
Installation examples ................................61
Drawing for dismantling and assembly .............62
Declaration of conformity ..................................64
A,AS Rev13.indd 8
11/06/15 10:49
