Burster DIGIFORCE 9311 Скачать руководство пользователя страница 65

Страница: 65 / 216

of 216

6.1.17 PROFINET settings (option)

Note:

The "PROFINET" menu (M76) only exists if your DIGIFORCE

9311 is installed with option

Vxxx3.

Diagram 29: PROFINET settings – page 1

Parameters in the "PROFINET" menu (M76)

SW-version

Firmware version of the PROFINET Fieldbus module

Serial number

Serial number of the Fieldbus module

Control via

PROFINET

: the DIGIFORCE

9311 responds solely to control signals

(inputs) from the PROFINET interface.

PLC

: the DIGIFORCE

9311 responds solely to control signals (inputs)

from the PLC I/O interface.
When control via PLC I/O is selected, data is still transferred on the

PROFINET real-time channel.

Device MAC

Address for identifying the Fieldbus module in the PROFINET network.

Port1 MAC

Port 1 MAC address

Port2 MAC

Port 2 MAC address

Name of station

The station name assigned by the PROFINET host.

IP address

Assigned IP address

Please note

: this parameter cannot be changed in the DIGIFORCE

9311.

Содержание DIGIFORCE 9311

























































































































































































































Результаты поиска

Содержание DIGIFORCE 9311

Отзывы:

Бренды по названию

Популярные бренды

Burster DIGIFORCE 9311, Руководство по эксплуатации

Результаты поиска

Содержание DIGIFORCE 9311

Отзывы:

Бренды по названию

Популярные бренды