Burster DIGIFORCE 9311 Скачать руководство пользователя страница 198

Страница: 198 / 216

198

of 216

8.2.2 Measurement with measurement-data logging

The DigiControl PLUS PC software for the DIGIFORCE

9311 provides the option for automatic data

logging at the end of a measurement. When data logging is enabled, the "OUT_READY" signal, which

indicates that the instrument is in standby and ready to perform another measurement, is not set until

data transmission is complete. The time taken for data logging depends on the choice of communication

interface and on the size of the measurement curve. The time length for data logging shown in the signal

timing diagram is the time typically taken when the Ethernet port is used.

Diagram 92: With measurement-data logging

*You can define a configurable PLC output for the signal "OUT_PC_LOGGING".

Cycle

a. DigiControl PLUS (PC software) sets the signal "OUT_PC_LOGGING" to 1 when

measurement mode starts.

b. The controller (PLC) checks whether the DIGIFORCE

9311 is ready

("OUT_READY" =1).

c. The PLC starts the measurement with "IN_START" = 1
d. During the measurement phase the DIGIFORCE

9311 sets the signals "OUT_OK“

and "OUT_NOK" to 1 and the signal "OUT_READY" to 0.

e. The PLC stops the measurement by resetting the signal "IN_START" to 0.
f. The DIGIFORCE

9311 updates the result during the evaluation phase:

"OUT_OK" = 1 and "OUT_NOK" = 0: measurement OK

"OUT_OK" = 0 and "OUT_NOK" = 1: measurement NOK

g. At the end of the evaluation phase, the DIGIFORCE

9311 sets the signal

"OUT_READY" to 1 (in standby).

DigiControl PLUS sets “OUT_PC_LOG = 0” at the end of the measurement.

Tip

To optimize cycle times, the PLC can retrieve the OK/NOK evaluation immediately after the measurement

rather than waiting for the READY signal, which it can check before the next measurement.

Содержание DIGIFORCE 9311

























































































































































































































Результаты поиска

Содержание DIGIFORCE 9311

Отзывы:

Бренды по названию

Популярные бренды

Burster DIGIFORCE 9311, Руководство по эксплуатации

Результаты поиска

Содержание DIGIFORCE 9311

Отзывы:

Бренды по названию

Популярные бренды