Burster DIGIFORCE 9311 Скачать руководство пользователя страница 197

Страница: 197 / 216

197

of 216

8.2 Starting a measurement

Instead of using external signals, you can also use separate internal events to start and stop a

measurement in the DIGIFORCE

9311. You define the necessary settings for this in the Measurement

mode configuration menu; for details, please see section 6.3.2.4 "Start/Stop mode" on page 113.

8.2.1 Measurement without measurement-data logging

Standard measurement cycle without active logging of measurement data via the communication

interfaces (Ethernet, USB). For a Fieldbus interface, all result values are immediately available once

"OUT_READY" = 1.

Diagram 91: Without measurement-data logging

Cycle

a. The controller (PLC) checks whether the DIGIFORCE

9311 is ready

("OUT_READY" =1).

b. The PLC starts the measurement with "IN_START" = 1
c. During the measurement phase the DIGIFORCE

9311 sets the signals "OUT_OK“

and "OUT_NOK" to 1 as well as the signal "OUT_READY" to 0.

d. The PLC stops the measurement by resetting the signal "IN_START" to 0.
e. The DIGIFORCE

9311 updates the result during the evaluation phase:

"OUT_OK" = 1 and "OUT_NOK" = 0: measurement OK

"OUT_OK" = 0 and "OUT_NOK" = 1: measurement NOK

f. At the end of the evaluation phase, the DIGIFORCE

9311 sets the signal

"OUT_READY" to 1 (in standby).

Note:

As soon as the process has finished, the PLC (I/O or Fieldbus) can withdraw the Start signal to

stop the measurement phase. This applies only when an external Stop has been selected. If an

external Stop has not been configured, the Start can be withdrawn even before the end of the
process. After detecting the Stop, the DIGIFORCE

9311 evaluates the recorded measured

values and sets the evaluation signals OK or NOK. The other evaluation signal in each case is

set to “0”. Once the full sequence has finished, the DIGIFORCE

9311 sets the READY signal.

Содержание DIGIFORCE 9311

























































































































































































































Результаты поиска

Содержание DIGIFORCE 9311

Отзывы:

Бренды по названию

Популярные бренды

Burster DIGIFORCE 9311, Руководство по эксплуатации

Результаты поиска

Содержание DIGIFORCE 9311

Отзывы:

Бренды по названию

Популярные бренды