background image

Page 15 of 20 

 

14.

 

Points to Note Regarding the Catalytic Convertor!  

 

 

 

If  the  customer  smokes  tobacco  products,  lives  on  a  busy  road  or  is  cooking  with  a  gas 
oven/hob  at  the  time  of  testing  you  must  ensure  that  an  ambient  CO  reading  is  taken 
before lighting the fire and attempting a reading.  

 

 

Does  the  catalytic  convertor  need  replacing? 

The  catalytic  convertor  does  not  need 

replacing  unless  it  has  become  physically  broken  or  the  combustion  test  shows 
deterioration  in  performance  over  time.  To  constantly  test  the  performance  of  the 
catalytic converter, our laboratory has been running appliances eight hours per day, five 
days per week, for up to seven years. Periodically we send catalytic converters back to the 
manufacturer for testing. After the equivalent of 30 years of use, the catalytic converter is 
as  efficient  as  it  was  when  brand  new.  Burley  manages  to  achieve  this  by  designing  the 
fire to ensure that the catalytic converter is in exactly the right position for long life and 
maximum efficiency. (For other makes of fire please consult the relevant manufacturer). 
Only use replacement catalyst supplied by Burley.  

 

 

If  you  or  the  customer  detects  any  odours  from  the  fire  please  remember  that  the 
catalytic convertor is not an air filter and does not remove smells. The ceramics in the fire 
can  absorb  household  smells  and  in  turn  these  smells  get  emitted  when  the  fire  is  lit, 
especially if the fire is used in an enclosed space for a period of time. If this is the case we 
recommend  that  the  fire  is  run  on  maximum  for  at  least  5  hours  with  the  doors  and 
windows  open.  This  should  be  done  at  least  twice  a  year,  preferably  in  the  spring  and 
autumn or at any time they notice a smell.  

 

 

We do not advise the burning of wax candles within 1 metre of the fire. Wax particles can 
become  airborne  and  deposit  and  solidify  in  the  fire  causing  potential  combustion 
problems.  

 

 

The catalyst can also be affected by airborne paint smells and vapours from some plug in 
air  fresheners.  The  fire  must  be  removed  or  sealed  if  you  plan  to  decorate  anywhere  in 
the house.  If  you  can  detect  smells  from  the fire  carry  out  the burning off procedure  as 
above.  

 
 
 

Further information regarding the catalytic convertor and Flueless fires in general can 
be found on our website 

www.burley.co.uk

  

Содержание LONGITUDE





















Отзывы: