80
How to do the settings
Type 8098 FLOWave L
10
HOW TO DO THE SETTINGS
10.1
Safety instructions
WARNING
Risk of injury due to non-conforming adjustment.
Non-conforming adjustment could lead to injury and damage the device and its surroundings.
▶
The operators in charge of adjustment must have read and understood the contents of the Operating
Instructions.
▶
In particular, observe the safety recommendations and intended use.
▶
The device/installation must only be adjusted by suitably trained staff.
10.2
Available software to do the settings
The settings of the device can be done with:
•
the Type ME31 display module. The device can be equipped with a display module or not.
• the Type 8920 Bürkert Communicator software, which must be installed on a PC.
The menu structure is the same in the display module and in the Bürkert Communicator software.
→
To do the settings of the device with the Type ME31 display module, refer to the next chapters of these
Operating Instructions, starting with chapter 10.4 Display module: description of the user interface
.
→
To use the Bürkert Communicator software, first prepare the necessary hardware and the software. Refer to
chapter 10.3. Then do the settings as described in these Operating Instructions, starting with chapter 10.4.3
Minimum and maximum values when entering a numerical value
→
To use some specific functions that are only available with the Bürkert Communicator software, refer to
the Type 8920 Operating Instructions, available on the internet at
.
→
To get detailed information on the software of the Type ME31 display module, refer to the related Oper
-
ating Instructions, available on the internet at
10.3
Connect the device to the Bürkert Communicator
software
To do the settings with the Type 8920 Bürkert Communicator software, do the following steps:
1. Buy the USB-büS interface set with article number 772426 from Bürkert.
2. Download the latest version of the Type 8920 Bürkert Communicator software from
.
3. Install the Bürkert Communicator software on a PC. Obey the installation recommendations given in the
USB-büS interface set. During installation, the büS stick must not be inserted at the PC.
4. Screw the termination resistance into the Y plug or activate the device internal termination resistor (see
chapter 12.6.3
).
5. Screw the female M12 connector at the end of the delivered cable into the Y plug.
English
Содержание Flowave 8098
