manualshive.com logo in svg

Buell Ulysses 2006, Руководство по обслуживанию

Service Manual для Buell Ulysses 2006 теперь доступен для скачивания бесплатно на manualshive.com. Этот руководство поможет вам провести ремонт и обслуживание вашего мотоцикла самостоятельно. Не тратьте время зря, скачайте его прямо сейчас!

Поделиться
Скачать
background image

 

2006 Buell Uylsses: Maintenance

1-33

 

HOME

 

SUSPENSION DAMPING ADJUSTMENTS

1.11

 

GENERAL

1

WARNING

1

WARNING

 

Before evaluating and adjusting suspension settings,
check the motorcycle’s tires. Be sure tires are properly
inflated, balanced and have adequate tread. Inspect your
tires regularly and see a Buell dealer for replacements.
Riding with excessively worn, unbalanced or under-
inflated tires can adversely affect stability and handling,
which could result in death or serious injury. (00114a)

 

Make all suspension adjustments in one or two click incre-
ments. Adjusting more than one or two clicks at a time may
cause you to skip the best adjustment. Test ride after each
adjustment. When an adjustment makes no difference, return
to the previous adjustment and try a different approach.

If both preload adjustments are correct, and you have the
rebound and compression damping set at the factory recom-
mended points, the motorcycle should handle and ride prop-
erly. If you wish to fine tune these settings they can be
changed according to the following procedures.

 

NOTE

Evaluating and changing the rebound and compression
damping is a very subjective process. Many variables affect
motorcycle handling under different circumstances. Approach
all changes carefully and consult 

Table 1-10.

 

FINE TUNING  SUSPENSION:

 

BUELL MODELS

 

The settings are the best balance of handling, ride, and sta-
bility. Suspension can be changed to accommodate rider
preferences for ride quality and handling for road conditions
and load changes.

 

NOTES

 

●

 

Do not continue to repeat the steps involved with the fol-
lowing settings beyond those which are listed.

 

●

 

Adjust suspension to the recommendation if possible, but
never force adjusters beyond the mechanical stops.

1

WARNING

1

WARNING

 

Do not operate motorcycle with loose, worn or damaged
steering or suspension systems. Contact a Buell dealer
for repairs. Loose, worn or damaged steering or suspen-
sion components can adversely affect stability and han-
dling, which could result in death or serious injury.
(00113a)

 

Changes in Load

 

Changes in the load carried requires changes in the preload
setting(s). Carrying less weight than was used for setting up
the suspension requires decreasing the amount of preload.
Increasing the load carried requires adding more preload.

1

WARNING

1

WARNING

 

Do not exceed the motorcycle Gross Vehicle Weight Rat-
ing (GVWR). Exceeding the GVWR can affect stability
and handling, which could result in death or serious
injury. (00016a)

 

●

 

GVWR is the sum of the weight of the motorcycle, acces-
sories, and the maximum weight of the rider, passenger
and cargo that can be safely carried.

 

●

 

The GVWR is shown on the information plate, located on
the frame steering head.

 

Ride Quality Enhancement

 

The stock settings are designed to offer sufficient chassis
control, but some may choose to enhance ride comfort over
rougher road conditions or for long rides. Adjusting the com-
pression setting will reduce both high and low speed damp-
ing.

1.

Adjust suspension for rider weight. Refer to 

Table 1-10.

2.

Increase ride quality by reducing front and rear compres-
sion damping by turning adjuster counterclockwise 1/4-1
turn.

3.

If additional ride quality is desired, reduce front preload
by  turning adjuster counterclockwise until an additional
line is visible and also reduce rear preload 1 position.

4.

If maximum ride quality is desired, decrease front and
rear rebound damping by turning adjusters counterclock-
wise by 1/4-1/2 turn.

 

Enchanced Steering Quickness

 

The response to steering input (quickness) may be enhanced
by  adjusting the vehicles front/rear ride height. This adjust-
ment effectively decreases the vehicles rake angle. This is
achieved by adjusting the preload to increase front sag and
reduce rear sag.

1.

Adjust suspension for rider weight. Refer to 

Table 1-10.

2.

Reduce steering effort by increasing the rear preload
one position.

3.

If more enhanced steering and cornering control is
desired, reduce front preload by turning adjuster counter-
clockwise until an additional line is visible.

4.

If additional enhanced steering and cornering control is
desired, increase rear compression damping by turning
adjuster clockwise by 1/4-1/2 turn.

5.

If maximum enhanced steering and cornering control is
desired, increase front rebound damping by turning
adjuster clockwise 1/4 turn.

Содержание Ulysses 2006































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Ulysses 2006

CUSTOMACCES SEMIFARINGS ANARCHY Mounting Instructions preview
SEMIFARINGS ANARCHY
Бренд: CUSTOMACCES Страницы: 2
Happy Trails KTM950 Quick Start Manual preview
KTM950
Бренд: Happy Trails Страницы: 4
Razor Rebellion Electric Chopper 15130760 Owner'S Manual preview
Rebellion Electric Chopper 15130760
Бренд: Razor Страницы: 17
Denali SoundBomb TT-SB.10100.B Instruction Manual preview
SoundBomb TT-SB.10100.B
Бренд: Denali Страницы: 3
yasuni TUB225 Assembly Instructions Manual preview
TUB225
Бренд: yasuni Страницы: 12
Triumph Daytona 675 2014 Owner'S Handbook Manual preview
Daytona 675 2014
Бренд: Triumph Страницы: 162
hepco & becker 504980 00 05 Quick Manual preview
504980 00 05
Бренд: hepco & becker Страницы: 2
Pagsta BOBBER User Manual preview
BOBBER
Бренд: Pagsta Страницы: 47
Legend AXEO 0414-0545 Installation Manual preview
AXEO 0414-0545
Бренд: Legend Страницы: 2
tucanourbano TERMOSCUD-R204X Instruction Manual preview
TERMOSCUD-R204X
Бренд: tucanourbano Страницы: 2
tucanourbano TERMOSCUD R200X Instruction Manual preview
TERMOSCUD R200X
Бренд: tucanourbano Страницы: 4
tucanourbano TERMOSCUD R192X Instruction Manual preview
TERMOSCUD R192X
Бренд: tucanourbano Страницы: 4
MT Helmets TRIAL Series Owner'S Manual preview
TRIAL Series
Бренд: MT Helmets Страницы: 9
RSI HA1002 Installation Instructions preview
HA1002
Бренд: RSI Страницы: 2
Petzl A48 Manual preview
A48
Бренд: Petzl Страницы: 21
hepco & becker 6707597 00 01 Mounting Instructions preview
6707597 00 01
Бренд: hepco & becker Страницы: 3
hepco & becker 8007505 00 01 Quick Start Manual preview
8007505 00 01
Бренд: hepco & becker Страницы: 2
Biketronics RetroRadio BT100 Installation Manual preview
RetroRadio BT100
Бренд: Biketronics Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды