manualshive.com logo in svg

Buell Ulysses 2006, Руководство по обслуживанию, Страница: 409 / 638

Поделиться
Скачать
Buell Ulysses 2006 Скачать руководство пользователя страница 409

 

2006 Buell Ulysses: Fuel System

4-67

 

HOME

 

TROUBLE CODES 23 AND 32

4.22

 

GENERAL

 

Front Fuel Injector (Code 23)
And Rear Fuel Injector (Code 32)

 

See 

Figure 4-44.

 The fuel injectors (2,5) are solenoids that

allow pressurized fuel into the engine intake tract. The injec-
tors are timed to the engine cycle and are triggered sequen-
tially. 

 

NOTE

Front and rear injectors are not interchangeable due to spe-
cific spray patterns designed for the engine.

 

The power for the injectors comes from the ignition relay. The
ignition relay also provides power for fuel pump, ECM and the
ignition coils. The ECM provides the path to ground to trigger
the injectors.

 

NOTE

Ignition relay failures or wiring harness problems will cause
12 volt power to be lost to both injectors, ignition coils, ECM
and fuel pump.

 

DIAGNOSTICS

 

Diagnostic Notes

 

The reference numbers below correlate with the circled num-
bers on the Code 23/32 flow charts.

1

WARNING

1

WARNING

 

To prevent spray of fuel, purge system of high-pressure
fuel before supply line is disconnected. Gasoline is
extremely flammable and highly explosive, which could
result in death or serious injury. (00275a)

 

1.

Purge fuel line. See 

4.39 FUEL PUMP

.

2.

Use HARNESS CONNECTOR TEST KIT (Part No. HD-
41404), purple pin probes and patch cord.

3.

Connect BREAKOUT BOX (Part No. HD-42682) to ECM.
See 

4.6 BREAKOUT BOX

.

4.

Use FUEL INJECTOR TEST LAMP (Part No. HD-34730-
2C).

 

Figure 4-44. Fuel Injectors

Figure 4-45. Fuel Injector Connector

2

5

1.

Rear fuel injector

2.

Fuel rail assembly

3.

Clip (2)

4.

Front fuel injector

5.

Fuel rail fastener

10644

4

1

3

3

5

8822

1.

Fuel injector connector

2.

Tab

1

2

2

Содержание Ulysses 2006































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов