manualshive.com logo in svg

Buell Ulysses 2006, Руководство по обслуживанию, Страница: 226 / 638

Поделиться
Скачать
Buell Ulysses 2006 Скачать руководство пользователя страница 226

2-102

2006 Buell Ulysses: Chassis

HOME

SEAT LOCK

2.46

REMOVAL

1.

Remove seat. See 

2.45 SEAT

.

2.

Cut cable strap securing wire harness to seat lock cable.

3.

See 

Figure 2-136.

 Disconnect seat lock cable (5):

a. 

Remove latch (8) from latch bracket (9) by removing
two fasteners (7).

b. 

Remove cable end (6) and cable (5) from latch (8).

4.

Remove seat lock:

a. 

Remove wire cover from bottom side of license plate
bracket to access seat lock.

b. 

Remove seat lock retainer (3) from seat lock (1).

c.  Remove seat lock (1) from plate (2) and license

plate bracket.

NOTE

When removing seat lock (1), cable end (4) should release
from seat lock.

5.

Remove cable (5) from plate (2).

INSTALLATION

1.

See 

Figure 2-136.

 Install cable (5) into plate (2).

2.

Install the seat lock (1) into license plate bracket and
plate (2).

NOTES

●

Once seat lock has been started through the hole in the
license plate bracket and plate (2), now is the time to
connect the cable end to the seat lock.

●

Seat lock plate must be aligned to tab on seat lock for
proper installation.

3.

Install seat lock retainer (3) by aligning retainer to
retainer grooves on back side of seat lock (1).

4.

Connect seat lock cable to latch:

a. 

Install cable end (6) and cable (5) onto latch (8).

b. 

Install latch (8) to latch bracket (9) and tighten fas-
teners (7) to 72-96 in-lbs (8-10.8 Nm).

5.

Open and close the seat lock with ignition key to verify
that cable is working properly.

6.

Install the wire cover fasteners.

1

1

WARNING

1

WARNING

After installing seat, pull upward on front of seat to be
sure it is in locked position. While riding, a loose seat can
shift causing loss of control, which could result in death
or serious injury. (00070a)

7.

Install cable strap around seat lock cable in original loca-
tion.

8.

Install seat. See 

2.45 SEAT

.

Содержание Ulysses 2006































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов