background image

FLUIDS

tmo2011-001-075_a

1. Dipstick

2. Reinstall dipstick, screw in it completely.

3. Remove and check oil level. It should be near

or equal to the upper mark.

tmo2011-001-076_a

TYPICAL

1. MIN
2. MAX
3. Operating range

To add oil, remove the dipstick. Place a funnel into
the dipstick tube.

Add a small amount of recommended oil and
recheck oil level.

Repeat the above procedures until oil level
reaches the dipstick upper mark.

NOTE:

Do not overfill. Wipe off any spillage.

Properly tighten dipstick.

Engine Coolant

Recommended Engine Coolant

COOLANT HEADER

BRP recommended

product

LONG LIFE ANTIFREEZE

(P/N 219 702 685)

Alternative if not

available

Distilled water and

antifreeze solution (50%

distilled water, 50%

antifreeze)

NOTICE

Always

use

ethylene-glycol

an-

tifreeze containing corrosion inhibitors specif-
ically for internal combustion aluminum en-
gines.

Engine Coolant Level Verification

WARNING

Check coolant level with engine cold.

Place vehicle on a level surface.

Open service cover.

tbl2011-001-036_a

1. Service cover

Remove radiator pressure cap.

tmo2011-001-313_b

1. Air filter housing cover
2. Coolant expansion tank cap
3. Radiator pressure cap

Ensure cooling system is full up to the pressure
cap seat.

PREDELIVERY

2014-2

35 / 54

Содержание Can-Am Commander 1000 DPS 2014























































Отзывы: